Phone +420 774 723 123 Cart · 0 · empty
IN STOCK
PTFE 8x6, TECHNOLINE, smooth PTFE Teflon tube without braid, Ø8×6mm, wall 1mm

PTFE 8x6, TECHNOLINE, smooth PTFE Teflon tube without braid, Ø8×6mm, wall 1mm

Cat. no.: PTFE 8x6
Manufacturer: TECHNOLINE
In stock 583 pcs
Our price excl. VAT
3,33 €
incl. VAT 21 %
4,03 €
Weight 0.1 kg
HS Code (Taric) 39173200
Country of origin CN

Description

PTFE 8x6, TECHNOLINE, smooth PTFE Teflon tube without braid, Ø8×6mm, wall 1mm

Ø8×6mmwall 1mm11bar−73 to +260°Cwithout braid

PTFE 8x6 is a smooth Teflon tube made of PTFE (polytetrafluoroethylene) of the TECHNOLINE brand, without stainless steel braid. The smooth tube 8×6mm is suitable where a larger bore than small dosing tubes is needed and the chemical resistance of PTFE is also important. The outer Ø8mm, actual bore Ø6mm and wall 1mm. are decisive for selection

The inner Ø6mm means a flow cross-section of 28.27mm²; a larger bore tends to be advantageous where a higher flow rate is required under given conditions. In addition to chemical resistance, it is necessary to assess the operating temperature, required pressure, line length and connection method.

Why choose PTFE instead of a standard plastic tube

  • PTFE excels in resistance to a wide range of aggressive chemicals and solvents. The specific medium and its concentration must always be checked for chemical compatibility.
  • Very low surface friction and a smooth inner surface help limit adhesion of some media and make flushing the line easier. However, this is not a guarantee of self-cleaning.
  • The material series is intended for a wide temperature range from −73 to +260°C. The choice of connection and pressure suitability at high temperature are assessed separately.
  • PTFE has low water absorption and, with a correctly chosen medium, offers stable properties for laboratory and process lines.

Typical use of this variant

  • Chemically resistant connection of laboratory instruments with higher media flow.
  • Stationary process liquid distribution with suitably selected fittings and seals.
  • Supply of mixtures, coatings and other technical media only after assessing their compatibility.

Technical parameters PTFE 8x6

Parameter Value Data source
Order designation PTFE 8x6 TECHNOLINE
Material PTFE – polytetrafluoroethylene Technical specifications
Design Smooth tube without metal braid TECHNOLINE
Outer diameter 8mm Dimensional specifications
Inner diameter 6mm Dimensional specifications
Wall thickness 1mm Nominal geometry
Inner cross-section 28.27mm² Nominal geometry
Internal volume per 1m 28.27ml/m Nominal geometry
Temperature range of the material series −73 to +260°C Manufacturer's catalogue, page 07
Working pressure – value declared by TECHNOLINE 11bar Manufacturer's catalogue, page 07
Burst pressure 36bar Manufacturer's catalogue, page 07
Bending radius for mounting – recommendation 40mm Manufacturer's catalogue, page 07
Weight per 1m 47,8g/m Manufacturer's catalogue, page 07

How to choose diameter, flow rate and length

Compared to PTFE 6×4mm, Ø8×6mm 2.25× has a larger inner cross-section but a lower catalogue working pressure: 11bar instead of 16bar. When dimensioning a distribution, the outer diameter alone is not enough: the inner bore determines the hydraulic cross-section and the volume of media remaining in the tube. The actual flow rate depends on viscosity, route length, pressure profile and the resistance of connected components.

Working pressure, temperature and operation

For the stated version, TECHNOLINE declares the working pressure 11bar and burst pressure 36bar. Burst pressure is a failure limit, not a permissible working pressure. The declared temperature resistance of the material series −73 to +260°C does not mean that the maximum working pressure applies simultaneously at the highest temperature. When designing the system, it is necessary to respect the temperature derating of pressure capacity, the length of exposure and the parameters of the fittings used.

Mounting and recommended accessories

  • When choosing a fitting, look for a matching outer Ø8mm. Dimensional match alone does not guarantee that a specific fitting is approved for PTFE, pressure and temperature.
  • For a fixed line, keep the recommended bending radius of at least 40mm; do not create sharp kinks or tensile stress near the fittings.
  • Cut the end of the tube square and without burrs. Determine the suitability of the seal, clamping system and mechanical fixing according to the documentation of the given assembly.
  • For applications with frequent dynamic bending, check the fatigue load; a smooth PTFE tube is not an automatic replacement for highly flexible hoses.

Frequently asked questions

What pressure does the catalogue state for PTFE 8×6mm?

For PTFE 8×6mm, the catalogue states a working pressure of 11bar and a minimum burst pressure of 36bar.

What does the larger bore Ø6mm bring?

The inner Ø6mm offers a flow cross-section of 28.27mm². The exact flow rate depends on viscosity, line length and differential pressure.

Can a PTFE tube be used at +260°C with the stated working pressure?

Not automatically. The temperature range describes the material series, while the permissible pressure at elevated temperature and the resistance of the connection require a separate assessment.

Technical documentation: manufacturer's catalogue for the PTFE material series, page 07, and the approved TECHNOLINE product specification. Data on the permissible parameters of a complete pressure assembly also depend on the fittings used, the medium and temperature.

Technical parameters

Objednací kódPTFE 8x6
VýrobceTECHNOLINE
Outer diameter8mm
Inner diameter6mm
ColourWhite

Ask about this product

Ask us about technical parameters, compatibility with your equipment, availability or a price for larger quantities. It helps if you tell us what application you need the product for — if it does not fit, we will recommend a more suitable type.

Kód k opsání. Pokud ho nepřečtete, klikněte na Načíst nový kód.
The question relates to product PTFE 8x6

By sending you agree to the processing of the data provided for the purpose of handling your question. We do not pass the data on to third parties.

Related products

Cookies on this website

We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.