Phone +420 774 723 123 Cart · 0 · empty
IN STOCK
PTFE 6x4, TECHNOLINE, smooth PTFE Teflon tube without braid, Ø6×4mm, wall 1mm

PTFE 6x4, TECHNOLINE, smooth PTFE Teflon tube without braid, Ø6×4mm, wall 1mm

Cat. no.: PTFE 6x4
Manufacturer: TECHNOLINE
In stock 216 pcs
Our price excl. VAT
2,97 €
incl. VAT 21 %
3,60 €
Weight 0.1 kg
HS Code (Taric) 39173200
Country of origin CN

Description

PTFE 6x4, TECHNOLINE, smooth PTFE Teflon tube without braid, Ø6×4mm, wall 1mm

Ø6×4mmwall 1mm16bar−73 to +260°Cwithout braid

PTFE 6x4 is a smooth Teflon tube made of PTFE (polytetrafluoroethylene) of the TECHNOLINE brand, without stainless steel braid. Size 6×4mm offers a balance between line bore and compact mounting; it suits fixed lines in laboratory, dosing and process modules. The outer Ø6mm, actual bore Ø4mm and wall 1mm. are decisive for selection

The Ø4mm bore provides a larger flow cross-section than 4×2.5mm, but leaves a small media volume compared to size 8×6mm. In addition to chemical resistance, it is necessary to assess the operating temperature, required pressure, line length and connection method.

Why choose PTFE instead of a standard plastic tube

  • PTFE excels in resistance to a wide range of aggressive chemicals and solvents. The specific medium and its concentration must always be checked for chemical compatibility.
  • Very low surface friction and a smooth inner surface help limit adhesion of some media and make flushing the line easier. However, this is not a guarantee of self-cleaning.
  • The material series is intended for a wide temperature range from −73 to +260°C. The choice of connection and pressure suitability at high temperature are assessed separately.
  • PTFE has low water absorption and, with a correctly chosen medium, offers stable properties for laboratory and process lines.

Typical use of this variant

  • Stationary media supply to dosing valves and chemically resistant pumps.
  • Short connections of laboratory setups where a clean and smooth inner tube surface is important.
  • Distribution of technical gases and selected chemical liquids according to the compatibility of the whole assembly.

Technical parameters PTFE 6x4

Parameter Value Data source
Order designation PTFE 6x4 TECHNOLINE
Material PTFE – polytetrafluoroethylene Technical specifications
Design Smooth tube without metal braid TECHNOLINE
Outer diameter 6mm Dimensional specifications
Inner diameter 4mm Dimensional specifications
Wall thickness 1mm Nominal geometry
Inner cross-section 12.57mm² Nominal geometry
Internal volume per 1m 12.57ml/m Nominal geometry
Temperature range of the material series −73 to +260°C Manufacturer's catalogue, page 07
Working pressure – value declared by TECHNOLINE 16bar Manufacturer's catalogue, page 07
Burst pressure 55bar Manufacturer's catalogue, page 07
Bending radius for mounting – recommendation 30mm Manufacturer's catalogue, page 07
Weight per 1m 34,2g/m Manufacturer's catalogue, page 07

How to choose diameter, flow rate and length

The flow cross-section of Ø4mm is approximately 2.56× larger than Ø2.5mm, but smaller than Ø6mm; the suitable dimension is determined by the flow rate and pressure loss. When dimensioning a distribution, the outer diameter alone is not enough: the inner bore determines the hydraulic cross-section and the volume of media remaining in the tube. The actual flow rate depends on viscosity, route length, pressure profile and the resistance of connected components.

Working pressure, temperature and operation

For the stated version, TECHNOLINE declares the working pressure 16bar and burst pressure 55bar. Burst pressure is a failure limit, not a permissible working pressure. The declared temperature resistance of the material series −73 to +260°C does not mean that the maximum working pressure applies simultaneously at the highest temperature. When designing the system, it is necessary to respect the temperature derating of pressure capacity, the length of exposure and the parameters of the fittings used.

Mounting and recommended accessories

  • When choosing a fitting, look for a matching outer Ø6mm. Dimensional match alone does not guarantee that a specific fitting is approved for PTFE, pressure and temperature.
  • For a fixed line, keep the recommended bending radius of at least 30mm; do not create sharp kinks or tensile stress near the fittings.
  • Cut the end of the tube square and without burrs. Determine the suitability of the seal, clamping system and mechanical fixing according to the documentation of the given assembly.
  • For applications with frequent dynamic bending, check the fatigue load; a smooth PTFE tube is not an automatic replacement for highly flexible hoses.

Frequently asked questions

What is the working pressure of PTFE 6×4mm?

For PTFE 6×4mm, the manufacturer's table states a working pressure of 16bar and a minimum burst pressure of 55bar.

When to choose size 6×4mm?

The Ø6/4mm size provides 12.57ml of internal volume per metre and is suitable as an intermediate step between a very thin tube and a larger Ø8/6mm. line

Can a PTFE tube be used at +260°C with the stated working pressure?

Not automatically. The temperature range describes the material series, while the permissible pressure at elevated temperature and the resistance of the connection require a separate assessment.

Technical documentation: manufacturer's catalogue for the PTFE material series, page 07, and the approved TECHNOLINE product specification. Data on the permissible parameters of a complete pressure assembly also depend on the fittings used, the medium and temperature.

Technical parameters

Objednací kódPTFE 6x4
VýrobceTECHNOLINE
Outer diameter6mm
Inner diameter4mm
ColourWhite

Ask about this product

Ask us about technical parameters, compatibility with your equipment, availability or a price for larger quantities. It helps if you tell us what application you need the product for — if it does not fit, we will recommend a more suitable type.

Kód k opsání. Pokud ho nepřečtete, klikněte na Načíst nový kód.
The question relates to product PTFE 6x4

By sending you agree to the processing of the data provided for the purpose of handling your question. We do not pass the data on to third parties.

Related products

Cookies on this website

We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.