PTFE 12x8, TECHNOLINE, smooth PTFE Teflon tube without braid, Ø12×8mm, wall 2mm
- Our price excl. VAT
- 5,68 €
- incl. VAT 21 %
- 6,88 €
Description
PTFE 12x8, TECHNOLINE, smooth PTFE Teflon tube without braid, Ø12×8mm, wall 2mm
PTFE 12x8 is a smooth Teflon tube made of PTFE (polytetrafluoroethylene) of the TECHNOLINE brand, without stainless steel braid. Size 12×8mm provides the largest bore of these five tubes and is intended mainly for larger fixed process lines where the chemical and temperature resistance of PTFE is utilised. The outer Ø12mm, actual bore Ø8mm and wall 2mm. are decisive for selection
A wall of 2mm and an outer Ø12mm mean a different geometry and mounting requirements than 12×10mm; the difference cannot be neglected when dimensioning the flow and choosing end fittings. In addition to chemical resistance, it is necessary to assess the operating temperature, required pressure, line length and connection method.
Why choose PTFE instead of a standard plastic tube
- PTFE excels in resistance to a wide range of aggressive chemicals and solvents. The specific medium and its concentration must always be checked for chemical compatibility.
- Very low surface friction and a smooth inner surface help limit adhesion of some media and make flushing the line easier. However, this is not a guarantee of self-cleaning.
- The material series is intended for a wide temperature range from −73 to +260°C. The choice of connection and pressure suitability at high temperature are assessed separately.
- PTFE has low water absorption and, with a correctly chosen medium, offers stable properties for laboratory and process lines.
Typical use of this variant
- Stationary transport of selected chemical liquids in industrial equipment.
- Connection of reservoirs, valves and dosing units with a larger required bore.
- Distribution of technical media where a resistant smooth inner surface and appropriate fixing are needed.
Technical parameters PTFE 12x8
| Parameter | Value | Data source |
|---|---|---|
| Order designation | PTFE 12x8 | TECHNOLINE |
| Material | PTFE – polytetrafluoroethylene | Technical specifications |
| Design | Smooth tube without metal braid | TECHNOLINE |
| Outer diameter | 12mm | Dimensional specifications |
| Inner diameter | 8mm | Dimensional specifications |
| Wall thickness | 2mm | Nominal geometry |
| Inner cross-section | 50.27mm² | Nominal geometry |
| Internal volume per 1m | 50.27ml/m | Nominal geometry |
| Temperature range of the material series | −73 to +260°C | Manufacturer's catalogue, page 07 |
| Working pressure – value declared by TECHNOLINE | 15.4bar | TECHNOLINE technical specifications |
| Burst pressure | 55bar | TECHNOLINE technical specifications |
| Bending radius for mounting – recommendation | 85mm | TECHNOLINE technical specifications |
| Weight per 1m | 136,7g/m | TECHNOLINE technical specifications |
How to choose diameter, flow rate and length
PTFE 12×8mm has a nominal wall of 2mm and a flow cross-section of 50.27mm². Compared to Ø10×6.5mm, the cross-section increases by approximately 51 %, but the bending radius also increases. When dimensioning a distribution, the outer diameter alone is not enough: the inner bore determines the hydraulic cross-section and the volume of media remaining in the tube. The actual flow rate depends on viscosity, route length, pressure profile and the resistance of connected components.
Working pressure, temperature and operation
For the stated version, TECHNOLINE declares the working pressure 15.4bar and burst pressure 55bar. Burst pressure is a failure limit, not a permissible working pressure. The declared temperature resistance of the material series −73 to +260°C does not mean that the maximum working pressure applies simultaneously at the highest temperature. When designing the system, it is necessary to respect the temperature derating of pressure capacity, the length of exposure and the parameters of the fittings used.
Mounting and recommended accessories
- When choosing a fitting, look for a matching outer Ø12mm. Dimensional match alone does not guarantee that a specific fitting is approved for PTFE, pressure and temperature.
- For a fixed line, keep the recommended bending radius of at least 85mm; do not create sharp kinks or tensile stress near the fittings.
- Cut the end of the tube square and without burrs. Determine the suitability of the seal, clamping system and mechanical fixing according to the documentation of the given assembly.
- For applications with frequent dynamic bending, check the fatigue load; a smooth PTFE tube is not an automatic replacement for highly flexible hoses.
Frequently asked questions
For PTFE 12×8mm, TECHNOLINE declares a working pressure of 15.4bar and a burst pressure of 55bar. Burst pressure is not a permitted operating pressure.
The inner bore of Ø8mm offers the largest flow area in this series; for correct function, the route length and fittings must also be dimensioned.
Not automatically. The temperature range describes the material series, while the permissible pressure at elevated temperature and the resistance of the connection require a separate assessment.
Technical documentation: manufacturer's catalogue for the PTFE material series, page 07, and the approved TECHNOLINE product specification. Data on the permissible parameters of a complete pressure assembly also depend on the fittings used, the medium and temperature.
Technical parameters
| Objednací kód | PTFE 12x8 |
|---|---|
| Výrobce | TECHNOLINE |
| Outer diameter | 12mm |
| Inner diameter | 8mm |
| Colour | White |
Ask about this product
Related products
PTFE 6x4, TECHNOLINE, smooth PTFE Teflon tube without braid, Ø6×4mm, wall 1mm
PTFE 6x4
2,98 €
excl. VAT · 3,60 € incl. VAT
PTFE 8x6, TECHNOLINE, smooth PTFE Teflon tube without braid, Ø8×6mm, wall 1mm
PTFE 8x6
3,34 €
excl. VAT · 4,04 € incl. VAT
PTFE 10x6.5, TECHNOLINE, smooth PTFE Teflon tube without braid, Ø10×6.5mm, wall 1.75mm
PTFE 10x6.5
4,69 €
excl. VAT · 5,68 € incl. VAT
PTFE 4x2.5, TECHNOLINE, smooth PTFE Teflon tube without braid, Ø4×2.5mm, wall 0.75mm
PTFE 4x2.5
1,85 €
excl. VAT · 2,24 € incl. VAT