TPGJ08-04, TECHNOLINE, plug-in reducer Ø8mm→Ø4mm
TPGJ08-04, TECHNOLINE, plug-in reducer Ø8mm→Ø4mm. A plug-in adapter into a push-in counterpart with a separate tube connection.
Rate 24,43 CZK per 1 EUR. Prices are indicative, invoicing is in Czech crowns.
Push-in fittings with a plug-in stem for inserting into another push-in fitting. Suitable for reductions and changes of direction. Choose by stem and tube diameter.
TPGJ08-04, TECHNOLINE, plug-in reducer Ø8mm→Ø4mm. A plug-in adapter into a push-in counterpart with a separate tube connection.
TPGJ10-06, TECHNOLINE, plug-in reducer Ø10mm→Ø6mm. A plug-in adapter into a push-in counterpart with a separate tube connection.
TPGJ12-08, TECHNOLINE, plug-in reducer Ø12mm→Ø8mm. A plug-in adapter into a push-in counterpart with a separate tube connection.
TPGJ06-04, TECHNOLINE, plug-in reducer Ø6mm→Ø4mm. A plug-in adapter into a push-in counterpart with a separate tube connection.
TPGJ08-06, TECHNOLINE, plug-in reducer Ø8mm→Ø6mm. A plug-in adapter into a push-in counterpart with a separate tube connection.
TPGJ10-08, TECHNOLINE, plug-in reducer Ø10mm→Ø8mm. A plug-in adapter into a push-in counterpart with a separate tube connection.
TPGJ12-10, TECHNOLINE, plug-in reducer Ø12mm→Ø10mm. A plug-in adapter into a push-in counterpart with a separate tube connection.
TPLJ04, TECHNOLINE, elbow plug-in adapter, tube Ø4mm. A plug-in adapter into a push-in counterpart with a separate tube connection.
TPLJ08, TECHNOLINE, elbow plug-in adapter, tube Ø8mm. A plug-in adapter into a push-in counterpart with a separate tube connection.
Prices include the recycling fee.
In this category, the public range contains plug-in reducers and Pneuflex elbow versions. When selecting, draw both ends of the part and determine which accepts the tube and which enters another fitting. The word barb alone is not enough to determine the counterpart. The decision must be based on the design drawing, especially when modifying an already assembled distribution.
Pneuflex describes PGJ as an adapter with a tube connection on one side and a plug-in end on the other. PLJ changes the connection direction between the tube and the push-in fitting by a right angle.
For your own selection sheet, create a sketch of interfaces A and B. For A, state the size of the accepted tube, for B the size and purpose of the receiving fitting. Do not automatically present a pair of numbers as two tube sockets. If you plan to connect two separate tubes of different sizes, also compare Reducing fittings. If it is only a change of direction, add to the comparison Elbow fittings.
Our own practical question is: what part of the adapter will protrude from the counterpart after assembly? Add the axis of the connecting line and the outline of the obstacle to the sketch. For several parts in a row, assess the total overhang and the accessibility of each detachable point. A short separate adapter can create an assembly that will be difficult to replace after surrounding components are fitted.
When choosing a plug-in adapter, prepare two service variants: removing the tube alone and removing the whole connected assembly. For each, mark the required path of movement. If another part blocks access, write its dismantling into the procedure already during design. This shows whether a space-saving connection also corresponds to the required method of maintenance and the accessibility of the counterpart.
Let us consider a hypothetical plug-in part 38 mm long, which according to the model sketch is inserted into the counterpart by 16 mm. The protruding length is 38 − 16 = 22 mm. Another connected model part adds 27 mm from the same interface, so the total overhang reaches 22 + 27 = 49 mm. If the designed space is only 45 mm, the assembly exceeds its limit by 4 mm. All inputs are our own dimensions, not parameters of the offered items. The example does not attribute load capacity to the fitting; it shows the need to calculate the assembled length from the same reference points.
Prepare the work procedure for a safely secured section without pressure. For your own check, mark separately the connection of the adapter with the counterpart and the connection with the connecting line. Record which point you will dismantle when replacing the tube and which when replacing the adapter. Leave access to both operations in the design. As part of acceptance, compare the actual overhang with the sketch before completing the guarding; this is where the different measurement origins become apparent.
PGJ sheet distinguishes insertion of the tube and the stem; for removal, the release collet on the receiving fitting is operated. In the sketch, therefore, mark the operating point of each connection.
Your own diagnostic record should distinguish a symptom at the stem and a symptom at the tube. It is not enough to state that the reducer leaks. Note whether the adapter, the receiving fitting or the line was changed, and record the full designation of each. Compare only verified pairs of parts. If you are looking for a new arrangement of the whole connection, return to the division of shapes in the category Push-in fittings.
Assess the interface according to the drawing of the specific part. The connection inside a soft tube cannot be automatically derived from the description of the plug-in connection into a fitting.
Check the whole interface and the intended use. The same number is not enough to confirm the counterpart, the assembled length or access for later dismantling.
We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.
Choose which cookies we may use. You can change your choice at any time.
They keep the cart contents, your login and selected language, and protect forms from abuse. An order cannot be completed without them, so they are used even without consent.
Google Analytics shows us traffic and behaviour on the website in aggregated form. This tells us which pages are not working for people. We do not identify anyone from this data.