PUC6X4-2BL, TECHNOLINE, coiled polyurethane pneumatic tube, 6×4mm, working length 2m, blue
- Our price excl. VAT
- 3,83 €
- incl. VAT 21 %
- 4,63 €
Description
PUC6X4-2BL, TECHNOLINE, coiled polyurethane pneumatic tube, 6×4mm, working length 2m, blue
PUC6X4-2BL is a polyurethane tube in the TECHNOLINE range. With a diameter of 6×4mm and a wall of 1mm, the inner cross-section is 12.57mm². The fitting is selected according to outer diameter Ø6mm, not by the inner bore 4mm. The coiled version has a declared working length of 2m and free ends for push-in fittings.
Technical parameters of the specific variant
| Parameter | Value |
|---|---|
| Order code | PUC6X4-2BL |
| Manufacturer | TECHNOLINE |
| Type | coiled PU tubes |
| Material | polyurethane (PU) |
| Outer diameter (OD) | 6mm |
| Inner diameter (ID) | 4mm |
| Wall thickness (calculation) | 1mm |
| Theoretical flow area (calculation) | 12.57mm² |
| Colour | blue |
| Declared working length of the coil | 2m |
| Coil termination | Free ends without fitted fittings |
Pressures, operating limits and bends
| Parameter | Value |
|---|---|
| Nominal working pressure | 10bar (1.0MPa) |
| Burst pressure | 30bar (3.0MPa) – failure limit, not working pressure |
| Declared temperature range | −20 to +60°C |
| Dependence of working pressure on temperature | At higher temperatures, the permissible pressure may decrease. The value 10bar cannot automatically be applied to +60°C. |
| Minimum radius of the PU tube itself | A separate material value is not documented for the specific compound; use the mounting recommendation for routing at the fitting below |
| Mounting radius of the line at a push-in fitting | R ≥ 30mm for OD Ø6mm – recommendation for the connection section, not an independently documented minimum bend of the tube material |
Why does a coil have a different mechanical load?
A coiled tube alternately extends and contracts during work. The tube material bends in the coils and at the transition to the straight ends. Do not allow tension to be transferred directly to the sealing neck of the fitting; routing and strain relief must correspond to the movement of the equipment.
Practical guide to material and pneumatic distribution
Why polyurethane?
A polyurethane tube combines compliance for distribution with moving sections, flexible bending and generally good abrasion resistance. PU allows the line to be routed around machine components where a stiffer tube would complicate routing. However, its capabilities vary according to the material subtype, temperature and specific composition.
For this version PUC6X4-2BL: A smaller inner bore is practical for short signal and control branches; however, at the same flow rate and length it can cause a higher pressure loss than a larger tube.
What affects the flow rate and cylinder response?
The inner diameter determines the geometric cross-section; the actual flow rate further depends on the line length, the flow coefficient of fittings and valves, the pressure differential and the compressibility of air. A doubled cross-section alone does not mean exactly double the actual flow rate.
Geometric calculation for PUC6X4-2BL: wall thickness = (6 − 4)/2 = 1mm. Theoretical cross-section A = π·4²/4 = 12.57mm². OD/ID ratio = 1.5. The calculation says nothing about pressure resistance.
Effect of temperature on working pressure
With higher temperature, the mechanical properties of PU and the permissible working pressure may change. When designing the line, respect the operating temperature and the lowest pressure limit of the whole assembly. The burst pressure cannot be used as the working pressure.
Line volume for this bore
One metre of tube with an inner diameter 4mm has a geometric volume of approximately 12.57ml. When a fast response of the pneumatic actuator is required, monitor the line length and the volume that needs to be pressurised or exhausted when the state changes. This is not a flow rate value or the volume of compressed air at operating pressure.
Space requirements of the distribution
The tube has an outer diameter of 6mm and a mounting radius of the line behind the fitting of 30mm. When designing a panel, this value can be used to plan the space for the outlet; temperature and dynamic loads must be assessed separately.
Colour blue makes it possible to visually distinguish this pneumatic branch from other routes in the equipment. However, the colour variant alone does not prove a different pressure rating or chemical resistance.
Working length 2m is declared by TECHNOLINE. The ends are free for mounting the corresponding fittings. Always limit mechanical overstretching, sharp kinks and tension acting directly on the fitting.
Suitable fittings from the TECHNOLINE e-shop
For size OD 6mm, you can choose from the following push-in fittings in the TECHNOLINE range. The matching outer diameter, tube material and working limit of the whole assembly are decisive.
| Version | Fitting code | Link to e-shop |
|---|---|---|
| Straight push-in fitting | TPU06 | Show offer |
| Elbow fitting 90° | TPV06 | Show offer |
| T-connector | TPE06 | Show offer |
| Y-connector | TPY06 | Show offer |
For a coil, prevent tensile stress on the fitting. Verify a straight end, insertion to the stop and a free route for movement.
Need a transition to a different diameter? Category Reducing fittings contains various dimensional combinations; select according to the actual OD values of both tubes.
Specific questions about the product
By outer diameter Ø6mm. The Ø4mm bore is used to assess the geometric cross-section, not the size of the push-in opening.
Yes. The stated 2m is the declared working length of this coil. The ends are free, without end fittings, for corresponding push-in fittings.
No. The value at 20°C is not automatically permissible at a higher temperature. The design must respect the temperature limitations of the exact material and the weakest element of the system.
Technical parameters
| Objednací kód | PUC6X4-2BL |
|---|---|
| Výrobce | TECHNOLINE |
| Diameter | 6x4mm |
| Length | 2m |
Ask about this product
Related products
PUC6x4-1.5BL, TECHNOLINE, coiled polyurethane pneumatic tube, 6×4mm, working length 1.5m, blue
PUC6x4-1,5BL
2,52 €
excl. VAT · 3,05 € incl. VAT
PUC8x5.5-2BL, TECHNOLINE, coiled polyurethane pneumatic tube, 8×5.5mm, working length 2m, blue
PUC8x5,5-2BL
3,20 €
excl. VAT · 3,87 € incl. VAT
PUC6x4-4BL, TECHNOLINE, coiled polyurethane pneumatic tube, 6×4mm, working length 4m, blue
PUC6x4-4BL
3,64 €
excl. VAT · 4,40 € incl. VAT
PUC6x4-4CL, TECHNOLINE, coiled polyurethane pneumatic tube, 6×4mm, working length 4m, clear
PUC6x4-4CL
3,83 €
excl. VAT · 4,63 € incl. VAT
PUC8x5.5-4CL, TECHNOLINE, coiled polyurethane pneumatic tube, 8×5.5mm, working length 4m, clear
PUC8x5,5-4CL
5,18 €
excl. VAT · 6,26 € incl. VAT