PUC6x4-1.5BL, TECHNOLINE, coiled polyurethane pneumatic tube, 6×4mm, working length 1.5m, blue
PUC6x4-1.5BL, TECHNOLINE, coiled PU tube 6×4mm, blue, working length 1.5m and free ends. Working pressure 10bar, temperature −20 to +60°C.
Rate 24,43 CZK per 1 EUR. Prices are indicative, invoicing is in Czech crowns.
Coiled tubes: reach, connection and movement
PUC6x4-1.5BL, TECHNOLINE, coiled PU tube 6×4mm, blue, working length 1.5m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC8x5.5-2BL, TECHNOLINE, coiled PU tube 8×5.5mm, blue, working length 2m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC6x4-4BL, TECHNOLINE, coiled PU tube 6×4mm, blue, working length 4m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC6x4-4CL, TECHNOLINE, coiled PU tube 6×4mm, clear, working length 4m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC6X4-2BL, TECHNOLINE, coiled PU tube 6×4mm, blue, working length 2m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC8x5.5-4CL, TECHNOLINE, coiled PU tube 8×5.5mm, clear, working length 4m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC6x4-15BL, TECHNOLINE, coiled PU tube 6×4mm, blue, working length 15m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC8x5.5-10BL, TECHNOLINE, coiled PU tube 8×5.5mm, blue, working length 10m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC 8x5.5 6M CL, TECHNOLINE, coiled PU tube 8×5.5mm, clear, working length 6m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC8x5.5-15BL, TECHNOLINE, coiled PU tube 8×5.5mm, blue, working length 15m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC10x6.5-10BL, TECHNOLINE, coiled PU tube 10×6.5mm, blue, working length 10m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC8x5.5-20BL, TECHNOLINE, coiled PU tube 8×5.5mm, blue, working length 20m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC 10x6.5 15M BL, TECHNOLINE, coiled PU tube 10×6.5mm, blue, working length 15m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC12x8-10BL, TECHNOLINE, coiled PU tube 12×8mm, blue, working length 10m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC12x8-15BL, TECHNOLINE, coiled PU tube 12×8mm, blue, working length 15m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC12x8-20BL, TECHNOLINE, coiled PU tube 12×8mm, blue, working length 20m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC10x6.5-20BL, TECHNOLINE, coiled PU tube 10×6.5mm, blue, working length 20m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC8x5.5-4BL, TECHNOLINE, coiled PU tube 8×5.5mm, blue, working length 4m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC6x4-10BL, TECHNOLINE, coiled PU tube 6×4mm, blue, working length 10m and free ends. Working pressure 10bar, temperature −20 to +60°C.
PUC6x4-20BL, TECHNOLINE, coiled PU tube 6×4mm, blue, working length 20m and free ends. Working pressure 10bar, temperature −20 to +60°C.
Prices include the recycling fee.
A coiled tube stores part of its length in coils. During operation it extends and returns to its original shape when released. Pneuflex describes this principle for the PUC family. When selecting, it is therefore essential where the operator needs to reach and how the line should behave when returning.
The range contains blue and clear PUC variants, for example PUC6x4-4BL and PUC6x4-10BL. Do not automatically interpret the length number in the name as a comfortable working reach. Before ordering, have the meaning of the stated length, the permitted extension and the end design of the specific item confirmed.
Mark the supply point, the normal working position and the most distant point of use. Add obstacles and the tool storage location to the sketch. For each position, write down where the tube should run and whether it must go around the edge of a table. This simple document provides a more accurate specification than a mere request for a "long coil".
Distinguish the material length, the length of the retracted coil and the working extension specified by the manufacturer. For the decision, you need the value corresponding to the intended movement. If the supplier states only one length without a definition, add a sketch to the enquiry; do not use an estimate from a photo as a mounting dimension.
Write down the tool's supply requirement and compare it with the whole route including connections. In the specification, separate the outer and inner diameter, the design of both ends and the scope of delivery. For PUC, the manufacturer distinguishes supplies with and without end fittings; therefore always verify the actual version for the selected item.
For a supply routed in a fixed way along the machine, compare Polyurethane PU tubes. Consider whether the whole route should be coiled, or only the section at the operator. Draw the division before ordering, including the accessibility of the joint. An overview of other materials is provided by the category Pneumatic tubes.
Our own tutorial example assumes a horizontal distance of 2.4 m and a height difference of 1.0 m between the supply and the working position. The straight line has a length of √(2.4² + 1.0²) = 2.6 m. In this model, the designer adds 0.4 m for the chosen detour around an obstacle, so the route assessed is 3.0 m long.
This is not the permitted extension of any offered tube nor a universal allowance. The result is a geometric requirement of the workplace that you must compare with the confirmed working reach of a specific coil. The model does not include the force needed for extension; assess it during a practical test in the intended working position.
Before mounting or disconnecting, shut off the supply and depressurise the line; this principle is stated in SMC instructions for pneumatic lines. For your own acceptance, we suggest going through all drawn positions and recording the behaviour of the tube and its ends.
Watch whether the line extends into the aisle, touches the work surface or obstructs tool storage. In case of problems, compare the state in the retracted and working position. Record the point of snagging, an unreturned coil or repeated contact with an edge. The observation helps decide whether to check the length, supply location, fixing or the condition of the tube itself.
Do not draw such a conclusion without the manufacturer's definition. Request the working extension value for the exact order code.
Select according to the drawn positions and the result of the operating test. Also assess tool storage and the space for the tube at rest, not just the extreme reach.
We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.
Choose which cookies we may use. You can change your choice at any time.
They keep the cart contents, your login and selected language, and protect forms from abuse. An order cannot be completed without them, so they are used even without consent.
Google Analytics shows us traffic and behaviour on the website in aggregated form. This tells us which pages are not working for people. We do not identify anyone from this data.