KQ2L02-M3G, SMC, elbow fitting 90°, tube Ø2mm, male M3
KQ2L02-M3G, SMC, elbow fitting 90°, tube Ø2mm, male M3. Elbow connection of the tube to threaded port M3; changes the line direction at the component.
Rate 24,43 CZK per 1 EUR. Prices are indicative, invoicing is in Czech crowns.
Elbow push-in fittings for changing the tube direction by 90°. Choose by tube diameter.
KQ2L02-M3G, SMC, elbow fitting 90°, tube Ø2mm, male M3. Elbow connection of the tube to threaded port M3; changes the line direction at the component.
KQ2L06-01A, SMC, elbow fitting 90°, tube Ø6mm, male R1/8. Elbow connection of the tube to threaded port R1/8; changes the line direction at the component.
KQ2L06-02AS, SMC, elbow fitting 90°, tube Ø6mm, male R1/4. Elbow connection of the tube to threaded port R1/4; changes the line direction at the component. With pre-applied thread seal.
M-3ALU-4, SMC, elbow fitting with hose barb, thread M3, tube Ø4mm. A hose barb fitting for a soft tube; it is not a standard push-in collet.
KQ2L06-M5A, SMC, elbow fitting 90°, tube Ø6mm, male M5. Elbow connection of the tube to threaded port M5; changes the line direction at the component.
KQ2L06-01AS, SMC, elbow fitting 90°, tube Ø6mm, male R1/8. Elbow connection of the tube to threaded port R1/8; changes the line direction at the component. With pre-applied thread seal.
KQ2L08-01AS, SMC, elbow fitting 90°, tube Ø8mm, male R1/8. Elbow connection of the tube to threaded port R1/8; changes the line direction at the component. With pre-applied thread seal.
KQ2V04-M5A, SMC, universal elbow fitting, tube Ø4mm, male M5. Elbow connection of the tube to threaded port M5; changes the line direction at the component.
KQ2L08-02AS, SMC, elbow fitting 90°, tube Ø8mm, male R1/4. Elbow connection of the tube to threaded port R1/4; changes the line direction at the component. With pre-applied thread seal.
KQ2L06-03AS, SMC, elbow fitting 90°, tube Ø6mm, male R3/8. Elbow connection of the tube to threaded port R3/8; changes the line direction at the component. With pre-applied thread seal.
KQ2L08-01A, SMC, elbow fitting 90°, tube Ø8mm, male R1/8. Elbow connection of the tube to threaded port R1/8; changes the line direction at the component.
KQ2V06-M5A, SMC, universal elbow fitting, tube Ø6mm, male M5. Elbow connection of the tube to threaded port M5; changes the line direction at the component.
KQ2VS04-M5A, SMC, universal elbow fitting with internal hexagon, tube Ø4mm, male M5. Elbow connection of the tube to threaded port M5; changes the line direction at the component.
KQ2L08-03AS, SMC, elbow fitting 90°, tube Ø8mm, male R3/8. Elbow connection of the tube to threaded port R3/8; changes the line direction at the component. With pre-applied thread seal.
KQ2L08-02A, SMC, elbow fitting 90°, tube Ø8mm, male R1/4. Elbow connection of the tube to threaded port R1/4; changes the line direction at the component.
KQ2L08-00A, SMC, elbow fitting 90°, 2× tube Ø8mm. Change of line direction by 90° without a sharp tube bend right at the joint.
KQ2L06-M6N1, SMC, elbow fitting 90°, tube Ø6mm, male M6. Elbow connection of the tube to threaded port M6; changes the line direction at the component. Nickel-plated brass threaded part, oval release…
KQ2L06-M5N1, SMC, elbow fitting 90°, tube Ø6mm, male M5. Elbow connection of the tube to threaded port M5; changes the line direction at the component. Nickel-plated brass threaded part, oval release…
KQ2L10-00A, SMC, elbow fitting 90°, 2× tube Ø10mm. Change of line direction by 90° without a sharp tube bend right at the joint.
M-5ALU-4, SMC, elbow fitting with hose barb, thread M5, tube Ø4mm. A hose barb fitting for a soft tube; it is not a standard push-in collet.
KQ2L10-01AS, SMC, elbow fitting 90°, tube Ø10mm, male R1/8. Elbow connection of the tube to threaded port R1/8; changes the line direction at the component. With pre-applied thread seal.
KQ2L10-02AS, SMC, elbow fitting 90°, tube Ø10mm, male R1/4. Elbow connection of the tube to threaded port R1/4; changes the line direction at the component. With pre-applied thread seal.
KQ2L10-03AS, SMC, elbow fitting 90°, tube Ø10mm, male R3/8. Elbow connection of the tube to threaded port R3/8; changes the line direction at the component. With pre-applied thread seal.
KQ2L10-04AS, SMC, elbow fitting 90°, tube Ø10mm, male R1/2. Elbow connection of the tube to threaded port R1/2; changes the line direction at the component. With pre-applied thread seal.
KQ2D04-00A, SMC, three-way delta manifold, 3× tube Ø4mm. Branching into three pneumatic branches; the flow is divided according to consumption and line resistance.
Prices include the recycling fee.
Select elbow fittings with a sketch of the actual space around the connection. Not only the turning of the line is important, but also the type of both ends and the position of adjacent components. The range includes standard, miniature and all-metal Pneuflex versions and various SMC families. When comparing, follow the plan view of the whole assembly, not just the elbow itself.
Pneuflex for the PV family states a connection of two tubes of the same size at a right angle. Drawings KQ2L from SMC distinguish an elbow with two tube inlets and an elbow with a plug-in stem.
In your own selection sketch, mark the inlet axis, outlet axis and outline of obstacles. Add the connection type to each end. For the threaded version, require the full thread designation and information on the specific sealing method. For the plug-in version, draw the counterpart into which the stem is to enter. If you are only changing the direction of two tubes, do not automatically start by selecting a threaded variant; first assess the required interfaces.
Our own question for a confined space is: will it be possible to replace the tube after the adjacent part is fitted? Therefore add space for operating the connection and pulling out the line to the outline. If a change of direction is not necessary, compare Straight fittings. If the plug-in adapter is to change an existing connection, also go through Barb fittings.
For adjacent ports, draw a common plan view of all elbows. A part that is suitable on its own does not yet confirm that the whole row can be assembled. For your own design, compare the mounting order and two possible height levels of the lines. For each variant, go through the tool path and the tube path during replacement. The envelope of simultaneously fitted components is decisive, which you will not see in a catalogue photo of a single piece.
Let us consider an explicitly hypothetical corner in which the designer reserved a dimension of 45 mm in both directions from the intersection of the axes for routing in an arc. An alternative model elbow has an outline up to 21 mm from the same intersection. The difference between the two plan envelopes is 45 − 21 = 24 mm on each axis. If we also set a service reserve of 10 mm, we need 21 + 10 = 31 mm for the elbow variant. All dimensions are our own assumptions, not the tube bending radius or dimensions of a specific fitting. The result compares space; it says nothing about pressure loss or permissible movement.
For your own mounting preparation, mark on the drawing from which point the height and lateral overhang are measured. Before intervention, verify the safe state of the system and zero pressure in the section being changed. After placing the part, compare the design orientation with the position of the surrounding holders. If a change of connection size is also needed, evaluate it separately via Reducing fittings. Adding another part to the sketch must update the spatial balance.
Pneuflex for PV describes inserting the tube and disconnecting it by pressing the collet. For the specific elbow, verify access to both control points.
For service, record whether the problem appeared after turning the assembly, after fixing the line or after replacing the counterpart. Distinguish a symptom on the tube side from a symptom on the threaded side. Your own comparison procedure should keep the same route and always change one verified part. If only the position of the surrounding holder differs, record this change too. Without an axis sketch, it is difficult to tell whether a selection error or an arrangement error is recurring.
Define the required movement separately. Setting the position during mounting and repeated rotation during operation are different requirements that must be confirmed by the documentation of the specific version.
Add the counterpart and a spatial sketch to the dimension. Two elbows for the same line can have different types of ends and thus require a different assembly.
We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.
Choose which cookies we may use. You can change your choice at any time.
They keep the cart contents, your login and selected language, and protect forms from abuse. An order cannot be completed without them, so they are used even without consent.
Google Analytics shows us traffic and behaviour on the website in aggregated form. This tells us which pages are not working for people. We do not identify anyone from this data.