Phone +420 774 723 123 Cart · 0 · empty
IN STOCK
TPU16x12BL, TECHNOLINE, polyurethane pneumatic tube, 16×12mm, blue

TPU16x12BL, TECHNOLINE, polyurethane pneumatic tube, 16×12mm, blue

Cat. no.: TPU16x12BL
Manufacturer: TECHNOLINE
In stock 337 pcs
Our price excl. VAT
3,06 €
incl. VAT 21 %
3,70 €
Weight 0.04 kg
HS Code (Taric) 39173900
Country of origin CN

Description

TPU16x12BL, TECHNOLINE, polyurethane pneumatic tube, 16×12mm, blue

TPU16x12BL is a polyurethane tube in the TECHNOLINE range. With a diameter of 16×12mm and a wall of 2mm, the inner cross-section is 113.1mm². The fitting is selected according to outer diameter Ø16mm, not by the inner bore 12mm.

OD Ø16mmID Ø12mmWall 2mmblue

Technical parameters of the specific variant

Parameter Value
Order code TPU16x12BL
Manufacturer TECHNOLINE
Type straight PU tubes
Material polyurethane (PU)
Outer diameter (OD) 16mm
Inner diameter (ID) 12mm
Wall thickness (calculation) 2mm
Theoretical flow area (calculation) 113.1mm²
Colour blue

Pressures, operating limits and bends

Parameter Value
Nominal working pressure 10bar (1.0MPa)
Burst pressure 30bar (3.0MPa) – failure limit, not working pressure
Declared temperature range −20 to +60°C
Dependence of working pressure on temperature At higher temperatures, the permissible pressure may decrease. The value 10bar cannot automatically be applied to +60°C.
Minimum radius of the PU tube itself A separate material value is not documented for the specific compound; use the mounting recommendation for routing at the fitting below
Mounting radius of the line at a push-in fitting R ≥ 350mm for OD Ø16mm – recommendation for the connection section, not an independently documented minimum bend of the tube material
The working pressure 10bar may not apply up to +60°C: at higher temperatures a pressure reduction may be necessary. The burst pressure 30bar is not an operating limit. The weakest component of the pneumatic distribution is decisive.

What does a small bending radius mean?

Bending the tube into too sharp an arc can make its inner profile oval, increase pressure loss and gradually fatigue the wall. The flexibility of PU alone does not replace the catalogue minimum radius for the exact variant.

Practical guide to material and pneumatic distribution

Why polyurethane?

A polyurethane tube combines compliance for distribution with moving sections, flexible bending and generally good abrasion resistance. PU allows the line to be routed around machine components where a stiffer tube would complicate routing. However, its capabilities vary according to the material subtype, temperature and specific composition.

For this version TPU16x12BL: A larger inner bore can help reduce pressure losses in long or flow-intensive branches, but needs more space for bending and correspondingly larger fittings.

What affects the flow rate and cylinder response?

The inner diameter determines the geometric cross-section; the actual flow rate further depends on the line length, the flow coefficient of fittings and valves, the pressure differential and the compressibility of air. A doubled cross-section alone does not mean exactly double the actual flow rate.

Geometric calculation for TPU16x12BL: wall thickness = (16 − 12)/2 = 2mm. Theoretical cross-section A = π·12²/4 = 113.1mm². OD/ID ratio = 1.33. The calculation says nothing about pressure resistance.

Effect of temperature on working pressure

With higher temperature, the mechanical properties of PU and the permissible working pressure may change. When designing the line, respect the operating temperature and the lowest pressure limit of the whole assembly. The burst pressure cannot be used as the working pressure.

Line volume for this bore

One metre of tube with an inner diameter 12mm has a geometric volume of approximately 113.1ml. When a fast response of the pneumatic actuator is required, monitor the line length and the volume that needs to be pressurised or exhausted when the state changes. This is not a flow rate value or the volume of compressed air at operating pressure.

Space requirements of the distribution

The tube has an outer diameter of 16mm and a mounting radius of the line behind the fitting of 350mm. When designing a panel, this value can be used to plan the space for the outlet; temperature and dynamic loads must be assessed separately.

Colour blue makes it possible to visually distinguish this pneumatic branch from other routes in the equipment. However, the colour variant alone does not prove a different pressure rating or chemical resistance.

Suitable fittings from the TECHNOLINE e-shop

For size OD 16mm, you can choose from the following push-in fittings in the TECHNOLINE range. The matching outer diameter, tube material and working limit of the whole assembly are decisive.

Version Fitting code Link to e-shop
Straight push-in fitting TPU16 Show offer
Elbow fitting 90° TPV16 Show offer

The cut must be square and clean. Insert the tube to the stop, mechanically verify retention and carry out a leak check on first pressurisation.

Specific questions about the product

Which dimension should be used to choose a fitting for TPU16x12BL?

By outer diameter Ø16mm. The Ø12mm bore is used to assess the geometric cross-section, not the size of the push-in opening.

How to verify the bend of tube TPU16x12BL?

For routing the tube at a Ø16mm push-in fitting, the recommended radius is R ≥ 350mm. This dimension is not the minimum radius of the tube itself.

Is the stated catalogue pressure safe for every temperature?

No. The value at 20°C is not automatically permissible at a higher temperature. The design must respect the temperature limitations of the exact material and the weakest element of the system.

Technical parameters

Objednací kódTPU16x12BL
VýrobceTECHNOLINE
Outer diameter16mm
Inner diameter12mm
ColourBlue

Ask about this product

Ask us about technical parameters, compatibility with your equipment, availability or a price for larger quantities. It helps if you tell us what application you need the product for — if it does not fit, we will recommend a more suitable type.

Kód k opsání. Pokud ho nepřečtete, klikněte na Načíst nový kód.
The question relates to product TPU16x12BL

By sending you agree to the processing of the data provided for the purpose of handling your question. We do not pass the data on to third parties.

Related products

Cookies on this website

We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.