TPY04, TECHNOLINE, Y-connector for Ø4mm tube
TPY04, TECHNOLINE, Y-connector for Ø4mm tube. Angled Y-branching for routing three branches with suitable tube geometry.
Rate 24,43 CZK per 1 EUR. Prices are indicative, invoicing is in Czech crowns.
Branch push-in fittings – T-pieces, Y-pieces and multiple manifolds – for branching the pneumatic line. Choose by tube diameter and shape.
TPY04, TECHNOLINE, Y-connector for Ø4mm tube. Angled Y-branching for routing three branches with suitable tube geometry.
TPE04, TECHNOLINE, T-connector for Ø4mm tube. Branching into three pneumatic branches; the flow is divided according to consumption and line resistance.
TPY06, TECHNOLINE, Y-connector for Ø6mm tube. Angled Y-branching for routing three branches with suitable tube geometry.
TPE06, TECHNOLINE, T-connector for Ø6mm tube. Branching into three pneumatic branches; the flow is divided according to consumption and line resistance.
TPY08, TECHNOLINE, Y-connector for Ø8mm tube. Angled Y-branching for routing three branches with suitable tube geometry.
TPE08, TECHNOLINE, T-connector for Ø8mm tube. Branching into three pneumatic branches; the flow is divided according to consumption and line resistance.
TPZA04, TECHNOLINE, cross fitting for Ø4mm tube. Cross connection of four pneumatic branches at a single point.
TPE10, TECHNOLINE, T-connector for Ø10mm tube. Branching into three pneumatic branches; the flow is divided according to consumption and line resistance.
TPY10, TECHNOLINE, Y-connector for Ø10mm tube. Angled Y-branching for routing three branches with suitable tube geometry.
TPZA06, TECHNOLINE, cross fitting for Ø6mm tube. Cross connection of four pneumatic branches at a single point.
TPE12, TECHNOLINE, T-connector for Ø12mm tube. Branching into three pneumatic branches; the flow is divided according to consumption and line resistance.
TPZA08, TECHNOLINE, cross fitting for Ø8mm tube. Cross connection of four pneumatic branches at a single point.
TPK04, TECHNOLINE, multi-way manifold for Ø4mm tube. A multi-way compressed air distributor for clear connection of consumer branches.
TPY12, TECHNOLINE, Y-connector for Ø12mm tube. Angled Y-branching for routing three branches with suitable tube geometry.
TPZA10, TECHNOLINE, cross fitting for Ø10mm tube. Cross connection of four pneumatic branches at a single point.
TPK06, TECHNOLINE, multi-way manifold for Ø6mm tube. A multi-way compressed air distributor for clear connection of consumer branches.
TPK08, TECHNOLINE, multi-way manifold for Ø8mm tube. A multi-way compressed air distributor for clear connection of consumer branches.
TPZA12, TECHNOLINE, cross fitting for Ø12mm tube. Cross connection of four pneumatic branches at a single point.
TPK10, TECHNOLINE, multi-way manifold for Ø10mm tube. A multi-way compressed air distributor for clear connection of consumer branches.
TPE03C, TECHNOLINE, miniature T-connector for Ø3mm tube. Branching into three pneumatic branches; the flow is divided according to consumption and line resistance. Miniature version.
TPE04C, TECHNOLINE, miniature T-connector for Ø4mm tube. Branching into three pneumatic branches; the flow is divided according to consumption and line resistance. Miniature version.
TPE06C, TECHNOLINE, miniature T-connector for Ø6mm tube. Branching into three pneumatic branches; the flow is divided according to consumption and line resistance. Miniature version.
TPE16, TECHNOLINE, T-connector for Ø16mm tube. Branching into three pneumatic branches; the flow is divided according to consumption and line resistance.
TPY16, TECHNOLINE, Y-connector for Ø16mm tube. Angled Y-branching for routing three branches with suitable tube geometry.
KQ2U06-00A, SMC, Y-connector, 3× tube Ø6mm. Angled Y-branching for routing three branches with suitable tube geometry.
Prices include the recycling fee.
Select a branch fitting according to the number and direction of the required branches. The range includes T and Y shapes, cross versions, manifolds, miniature and all-metal variants and SMC items. For the design, it is essential to draw the actual ports; the designation Y-connector may not describe the whole distribution plan you want to create.
Pneuflex for PE describes the connection of three tubes of the same size in a T arrangement. PY family connects three tubes of the same size in a Y arrangement. PZA family has four tube connections.
Our own selection procedure starts with a map: each port gets a designation, connection type and size. Then assign the individual consumers and their working phases. For consumers along the same route, consider a Y spatial arrangement; for a side branch, assess a T. If the branch sizes differ, open Reducing fittings and mark which port needs a change. Such a map is more specific than ordering by a pair of numbers.
In your own assessment of the distribution, distinguish the number of connected consumers and the number of consumers running simultaneously. Also write the required behaviour when one branch is replaced into the specification. Whether the rest of the equipment should continue in operation is a decision about the whole diagram. If you only need a change of direction without a new branch, compare Elbow fittings.
Pneuflex for PK describes the division of the supply into three side tube connections of the same size. For your own sketch, mark each port, including the common supply. The number of branches served is then not confused with the total number of interfaces. When designing the assembly, record whether the common route should end or continue at the given point; this choice must be addressed by the specific diagram and part documentation.
Let us assume three model consumers with consumption of 75, 110 and 90 litres per minute. For this calculation, all values are deliberately expressed at the same reference conditions. With full simultaneity, the sum is 75 + 110 + 90 = 275 litres per minute. With a controlled sequence that allows only one consumer to work at a time, the highest of the considered instantaneous consumptions is 110 litres per minute. This is our own balance example, not the flow rate of a fitting. The pressure loss of the distribution cannot be determined from the result; however, it shows why the selection specification must include time simultaneity, not just a list of connected equipment.
Prepare the work for a safely secured and depressurised affected section. For your own mounting check, transfer the port designations from the sketch to the individual lines and verify the space for replacing each branch. For an assembly with multiple ports, go through the service operations one by one; access to the front tube alone is not enough. If the distribution passes through a structural bulkhead, address this point separately via Bulkhead fittings.
Pneuflex for PE describes connecting by insertion and disconnecting by pressing the collet. When mounting a branch fitting, assess this action for each port separately.
Your own service record should distinguish a problem of one consumer from a symptom during simultaneous operation of several branches. Compare the same working phases and record which branches were active. A symptom only during simultaneous operation is a reason to verify the common part of the distribution; replacing the last Y-connector alone would not explain the cause. If the problem follows a specific branch, check its route, counterparts and completeness of the selection record.
For the design, do not assume uniformity from the shape alone. Specify consumption, branch lengths and their working conditions; the distribution must be assessed for the actual layout.
First redraw all ports and the line route. Dimensional match is only part of the selection; orientation and service access in the assembly are also decisive.
We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.
Choose which cookies we may use. You can change your choice at any time.
They keep the cart contents, your login and selected language, and protect forms from abuse. An order cannot be completed without them, so they are used even without consent.
Google Analytics shows us traffic and behaviour on the website in aggregated form. This tells us which pages are not working for people. We do not identify anyone from this data.