EO1007030, EAE, sheet steel distribution board, 1000×700×300mm (H×W×D), RAL7035
EO1007030, EAE: sheet steel control cabinet enclosure, outer dimensions 1000×700×300mm (H×W×D), RAL7035, with mounting plate, protection rating IP66.
Rate 24,43 CZK per 1 EUR. Prices are indicative, invoicing is in Czech crowns.
EAE, Rittal and Schneider sheet steel control cabinets with mounting plate for electrical installation and automation. Choose by dimensions, depth, doors and protection rating.
EO1007030, EAE: sheet steel control cabinet enclosure, outer dimensions 1000×700×300mm (H×W×D), RAL7035, with mounting plate, protection rating IP66.
Sheet steel control cabinet enclosure EAE, EO series, with dimensions 1200×800×300mm. The version is intended for larger wall-mounted assemblies of control, protective and installation elements…
EO1208040, EAE. control cabinet enclosure. 1200×800×400mm (H×W×D). IP66. pallet shipping 1 000 CZK.
Prices include the recycling fee.
Choose a sheet steel control cabinet enclosure according to the drawing of the future fitting and the installation conditions. In this category you will find, among others, the designations EAE EO, EM and ET, Rittal AX and Schneider Electric NSYS3D. The presence of different series does not mean a common mounting system. For the order, the complete code, the current version and the list of supplied parts are decisive.
Distinguish the width, height and depth of the enclosure from the dimensions of the mounting plate. Manufacturers may use a different order of numbers in the name. Also measure components that protrude inward from the doors: operators, switches or connectors. Compare the sum of their depth and the depth of the opposite assembly with the design drawing, not just with the outer contour.
The specific Rittal AX 1045000 according to the manufacturer card, has outer dimensions of 400 × 500 × 210 mm and a mounting plate of 350 × 475 mm. The card lists the plate and the gland plate as included in the delivery. These data apply to the stated model; they must not be transferred to other AX enclosures or similarly sized EAE ones.
The reserve can be expressed both as an area and as a specific free space. An equally large total area scattered between devices may not allow a single wider module to be added. In addition to the percentage, it is therefore useful to mark where a possible future assembly will actually fit.
For a model plate of 300 × 400 mm, the total geometric area is 120 000 mm². If the design reserves 30 000 mm² as a reserve, that is 25 %. The calculation says nothing about the load capacity of the plate, thermal clearances or the available depth. This is an author's brief for comparing two layouts, not a recommended percentage or product dimension.
For operation, it is important whether the doors can be opened after adjacent equipment has been installed and whether the service technician can reach the terminals. When designing the wiring to the doors, take their full movement into account. Choose glands according to the cables and installation conditions; their dimensions and positions must be confirmed before the holes are made.
For a steel enclosure, also evaluate the environment with regard to the surface and intended mechanical modifications. Take the requirements for edge treatment, protective bonding and mounting of accessories from the documentation of the specific manufacturer. The mere presence of a metal plate or the colour of the surface is no proof of a correctly implemented protective function.
State the manufacturer code, photos of the rating plate and entries, the dimension drawing and a list of accessories. An old designation with the note “replaced” is not enough to confirm mechanical conformity. Separately address cooling and heating; the dimensional requirement may not capture the thermal needs of the assembly.
Verify the scope of delivery for the selected code. Do not take the presence of a plate in an illustrative photo as a complete bill of materials.
Only after comparing the current drawings and mounting conditions. Similar outer dimensions alone do not confirm compatibility. For other designs, use the guide to control cabinet enclosures.
We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.
Choose which cookies we may use. You can change your choice at any time.
They keep the cart contents, your login and selected language, and protect forms from abuse. An order cannot be completed without them, so they are used even without consent.
Google Analytics shows us traffic and behaviour on the website in aggregated form. This tells us which pages are not working for people. We do not identify anyone from this data.