HKP04060R5A, EMAS, flexible cable chain, inner width 60mm, inner height 40 mm
HKP04060R5A EMAS – flexible cable chain, inner width 60mm, inner height 40 mm. Exact technical data for selecting the cable chain type.
Rate 24,43 CZK per 1 EUR. Prices are indicative, invoicing is in Czech crowns.
Electrical consumables – cable lugs and ferrules, cable glands, conduits and conduit glands, cable ties, cable chains, trunking and DIN rails, sockets and bells. Choose by conductor cross-section and mounting method.
HKP04060R5A EMAS – flexible cable chain, inner width 60mm, inner height 40 mm. Exact technical data for selecting the cable chain type.
Prices include the recycling fee.
Electrical consumables link the design of electrical equipment with its actual mechanical execution. A well-chosen terminal is no help if the conductor termination does not fit into it; a quality cable in turn needs a suitable wall entry and a well-thought-out route. This category brings together material for terminating, organising, protecting and fixing cabling as well as selected connection and doorbell devices. When selecting, it pays to proceed interface by interface, not just by brand or the nearest size.
For stranded conductors connected to suitable terminals, use insulated crimp ferrules; crimp cable lugs are used for a screw connection with a ring. A ferrule and a lug are therefore not two interchangeable variants of the same termination. They differ in contact shape, the space required for connection and the tool used to make the joint. The cross-section figure alone does not determine whether the termination suits a specific terminal.
For organising conductors inside a control cabinet, choose trunking and suitable fixing elements. A DIN rail carries devices; it is not a substitute for cable trunking. A conduit protects the route, while its end fitting handles the transition to the equipment. A cable gland works with the cable sheath and the opening in the wall. For moving equipment, routing cables in an energy chain is added. Each of these parts answers a different design question.
The conductor cross-section in mm² describes the conductive part. The outer diameter of an insulated conductor or of the whole cable in millimetres is a different dimension, needed for example when assessing the entry and the space. The length of the metal sleeve of a ferrule is not the same as the overall length with the insulating collar. The nominal thread of a gland, in turn, does not say how wide a cable its seal will actually accept.
In the working list, therefore record electrical and mechanical data separately. For termination, it is the cross-section, conductor construction and receiving terminal. For the entry, add the outer cable diameter, the thread or mounting hole, the wall thickness and the environment. The need to assess the cable, thread and sealing interface together is explained in the LAPP technical guide to cable glands. The specific ranges, however, must come from the data sheet of the product being ordered.
For a fixed installation, draw the route including entries into the control cabinet, slack at the doors and access to devices. For movement, also describe the stroke, the position of the fixed points, the smallest permissible cable radius and the duty cycle. Flexible cable chains choose as part of a moving system, not as a simple substitute for plastic trunking.
The chain length reflects the stroke arrangement and the allowance for the bend. The manufacturer igus distinguishes these relationships in its documentation for calculating energy chain length. The dimensional similarity of another series does not justify adopting its design tables. Already at the design stage, leave space for the end brackets and any chain guidance; the moving bend must not intrude into the operator area or adjacent mechanics.
For a crimped joint, the conductor, termination and crimping tool belong to a single work procedure. The suitability of this combination and the quality of workmanship are emphasised by Weidmüller in its ferrule documentation. Therefore use the collar colour as an aid to organising work, not as the sole proof of the cross-section. With a twin ferrule, the termination must also be permitted by the receiving terminal.
For a conduit, check its size and profile, compatibility of the fitting and how the route is fixed. For a cable tie, the permissible bundle, material and fixing method are essential. An adhesive base needs a suitable substrate; the mere presence of an adhesive layer is no proof of long-term load capacity in all positions. Each interface has its own conditions and the resulting assembly must meet them all at once.
Consider our own production plan for eight identical assemblies. Each has 24 separate stranded conductors and both ends are to be terminated with a single ferrule permitted by the terminals in question. The basic requirement is 8 × 24 × 2 = 384 pieces. Another twelve ferrules are needed for twelve test terminations. In total, the plan therefore counts on 396 pieces, not 192 based on the number of conductors.
If the selected order item contained one hundred pieces, four packs would cover exactly this model requirement. Such a calculation does not, however, merge different cross-sections or lengths into one item: with two types of termination, the quantities are itemised separately. Openings in the enclosure, glands, fixing bases and conduit ends are counted separately in the same way. The reserve is determined by your own production process; it is not a universal percentage.
For small material, a short internal description containing the function, size, series and order unit helps. On receipt, distinguish between a piece, a bag and a whole pack. In the workshop, keep similar terminations separate and attach information on the tool used. When repairing, do not select a replacement only by colour or photo; also compare the size of the contact part and the documentation of the connected equipment.
Socket and doorbell devices belong in this overview as separate functional parts. For sockets and plugs 230V / 400V the complete connection system is assessed; for a transformer, the powered appliance and its consumption. The mains part of the equipment must be designed and carried out by a qualified person. The designation of one part does not transfer the protection rating, current capacity or other properties to an arbitrarily assembled whole.
No. An oversized termination may fit the conductor or terminal poorly, and an unsuitable sealing range of a gland may not match the cable. The size must suit both sides of the joint.
Material is only one piece of information. Add the design series, dimensions, environment, mounting conditions and the function of the original part. For a repair, the complete order code is more useful than a general name.
We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.
Choose which cookies we may use. You can change your choice at any time.
They keep the cart contents, your login and selected language, and protect forms from abuse. An order cannot be completed without them, so they are used even without consent.
Google Analytics shows us traffic and behaviour on the website in aggregated form. This tells us which pages are not working for people. We do not identify anyone from this data.