Inductive sensor, NRN6-8GH40-E2-V1-FB, 233615, PEPPERL+FUCHS
Inductive sensor, NRN6-8GH40-E2-V1-FB, 233615, PEPPERL+FUCHS
Rate 24,43 CZK per 1 EUR. Prices are indicative, invoicing is in Czech crowns.
Factor 1 inductive sensors have the same switching distance for steel, stainless steel, aluminium, brass and copper. They are suitable where objects of different metals are detected. Choose by diameter, range and output.
Inductive sensor, NRN6-8GH40-E2-V1-FB, 233615, PEPPERL+FUCHS
Inductive sensor, NRB12-18GM40-E2-C-V1, 201474, PEPPERL+FUCHS
Inductive sensor, NRN30-30GS50-E2-V1, 208565, PEPPERL+FUCHS
Inductive sensor, NRN30-30GS50-E3-V1, 220824, PEPPERL+FUCHS
Inductive sensor, NRN30-30GM50-E2-V1, 189134, PEPPERL+FUCHS
Inductive sensor, NRN30-30GM50-E2-C-V1, 184399, PEPPERL+FUCHS
Inductive sensor, NRB50-FP-E2-P3-V1, 186631, PEPPERL+FUCHS
Inductive sensor, NRB50-FP-A2-P3-V1, 134473, PEPPERL+FUCHS
Inductive sensor, NRN75-FP-A2-P3-V1, 182199, PEPPERL+FUCHS
Inductive sensor, NRN75-FP-E2-C-P3-V1, 183429, PEPPERL+FUCHS
Inductive sensor, NRB50-FP-E2-C-P3-V1, 187797, PEPPERL+FUCHS
Inductive sensor, NRB50-FP-A2-C-P3-V1, 187795, PEPPERL+FUCHS
Inductive sensor, NRN75-FP-A2-C-P3-V1, 187796, PEPPERL+FUCHS
Prices include the recycling fee.
A Factor 1 inductive sensor is designed for approximately the same switching distance on the metals specified by the manufacturer. It helps when steel, aluminium or other metal parts alternate at one workstation. It reduces differences caused by the material, but does not eliminate the influence of the target's dimensions and position.
Browse sensors with correction factor 1
The range of a standard inductive sensor may decrease when the material changes. The correction factor expresses the ratio of the range for a given material to the reference target under defined conditions. It is not one universal table valid for all sensor designs.
Illustrative example: if a model has a rated range of 10 mm and the manufacturer specifies a correction factor of 0.4, for a particular metal, the approximate material-adjusted value is 4 mm. For reliable mounting, also take into account the assured switching distance, target size and operating tolerances. The figures are not parameters of the pictured model.
| Situation | Benefit of Factor 1 | Remaining verification |
|---|---|---|
| Same part shape made of different metals | Smaller change in range when the material changes. | Which metals and tolerances the manufacturer actually declares. |
| Very small component | Material compensation may help. | Size, thickness and effective area of the target. |
| Oblique or edge-on passage | The influence of the material can be reduced. | Direction of movement, orientation and switching time. |
| Welding fixture | Alternating materials may be easier. | Resistance to magnetic fields, spatter and heat. |
A small screw, thin foil and a wide sheet can create different conditions for the same sensor. An approximately uniform material factor does not guarantee identical switching when the geometry changes. If you change both the alloy and the shape of the part, assess the two influences separately.
The pictured LANBAO LR18X-U series is classified by the manufacturer as Factor 1. For the specific order code, check the range, mounting design and declared behaviour towards individual metals. Any resistance to magnetic interference is a separate parameter that must be compared with the application.
First determine the largest gap resulting from the sum of mounting tolerances, play and vibration. It must remain within the verified area of reliable switching for the hardest-to-detect part. At the same time, the smallest gap must prevent a collision. Simply adjusting by the indicator LED while moving the part by hand does not replace this check.
Respect surrounding metal and the specified spacing between sensors. The Factor 1 design does not change the rules for flush and non-flush mounting. Near several sensing heads, check mutual interference according to the manufacturer's installation data.
The result should be a common usable mounting position for all parts, not just the best distance achieved with one sample.
No. It describes the sensor's material behaviour. The output type, for example switching PNP or analogue, must be checked separately.
It depends on the declared materials, alloy, dimensions and target conditions. Verify the required behaviour on the real part.
Only if the specific design also meets the requirements for magnetic fields, temperature and spatter. The Factor 1 name alone does not guarantee these resistances.
Browse sensors with correction factor 1
Sensors for welding · All-metal design
For a specific selection, prepare the material and dimensions of the target, the working gap, the environmental conditions and the required electrical connection. An overview can be found in the categories Special sensors and Inductive sensors.
Technical documents: LANBAO: LANBAO LR18X-U. This guide helps with selection; binding parameters, wiring and mounting are defined by the documentation of the ordered model.
We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.
Choose which cookies we may use. You can change your choice at any time.
They keep the cart contents, your login and selected language, and protect forms from abuse. An order cannot be completed without them, so they are used even without consent.
Google Analytics shows us traffic and behaviour on the website in aggregated form. This tells us which pages are not working for people. We do not identify anyone from this data.