IB3001T2, IPF, high-temperature inductive sensor, M30 × 70mm, Sn 10mm, 10-35VDC, PNP, NO, PTFE cable 10 m, 3 wires
IB3001T2 from IPF is a high-temperature inductive sensor. M30, Sn 10 mm, 10–35 V DC, PNP, NO, PTFE cable 10 m, 3 wires.
Rate 24,43 CZK per 1 EUR. Prices are indicative, invoicing is in Czech crowns.
High-temperature inductive sensors operate at temperatures above the usual 70 °C – at furnaces, presses, dryers and forming machines. Choose by the operating temperature of the head, cable and connector and by the required range.
IB3001T2 from IPF is a high-temperature inductive sensor. M30, Sn 10 mm, 10–35 V DC, PNP, NO, PTFE cable 10 m, 3 wires.
IN306040 from IPF is a high-temperature inductive sensor. M30, Sn 13 mm, External amplifier, Connector, IP50.
IB306040 from IPF is a high-temperature inductive sensor. M30, Sn 10 mm, External amplifier, Connector, IP50.
IN306052 from IPF is a high-temperature inductive sensor. M30, Sn 13 mm, External amplifier, PTFE cable 10 m + connector M12, IP50.
IB306052 from IPF is a high-temperature inductive sensor. M30, Sn 10 mm, External amplifier, PTFE cable 10 m + connector M12, IP50.
IN500140 from IPF is a high-temperature inductive sensor. M50, Sn 25 mm, 10–35 V DC, PNP, NO, Connector.
IN506040 from IPF is a high-temperature inductive sensor. M50, Sn 25 mm, External amplifier, Connector, IP50.
IB3001S3 from IPF is a high-temperature inductive sensor. M30, Sn 8 mm, 10–35 V DC, PNP, NO, PTFE cable 16 m, 3 wires.
IN800150 from IPF is a high-temperature inductive sensor. M80, Sn 50 mm, 10 V-35 V, PNP, NO, IP65.
IN800152 from IPF is a high-temperature inductive sensor. M80, Sn 50 mm, 10–35 V DC, PNP, NO, Silicone cable 10 m.
IC1301L0 from IPF is a high-temperature inductive sensor. 66x12x12 mm, Sn 2 mm, 10–30 V DC, PNP, NO, Connector, 3 pins.
Inductive sensor, for temperatures up to 180°C, M18x1, length 70mm, DC,npn,no,Sn:8mm nb,10m silicone cable,VA
IB181152 from IPF is a high-temperature inductive sensor. M18, Sn 5 mm, NPN, Cable 10 m.
IB186051 from IPF is a high-temperature inductive sensor. M18, Sn 5 mm, External amplifier, PTFE cable 5 m + connector M12, IP50.
IB180252 from IPF is a high-temperature inductive sensor. M18, Sn 5 mm, 10–35 V DC, PNP, NC, Silicone cable 10 m, 3 wires.
IN306053 from IPF is a high-temperature inductive sensor. M30, Sn 13 mm, External amplifier, Cable 15 m.
IN800151 from IPF is a high-temperature inductive sensor. M80, Sn 50 mm, 10–35 V DC, PNP, NO, Silicone cable 5 m.
Inductive sensor, NCN25-F35-A2-250-V1, 187479, PEPPERL+FUCHS
Inductive sensor, NCN20-F35-A2-250-10M-V1, 187851, PEPPERL+FUCHS
Inductive sensor, NJ4-30GM-N-200, 106429, PEPPERL+FUCHS
Inductive sensor, NCN25-F35-A2-250-15M-V1, 187480, PEPPERL+FUCHS
Inductive sensor, NJ4-N-H31, 002244, PEPPERL+FUCHS
Inductive sensor, NCN20-F35-A2-250-20M-V1, 187524, PEPPERL+FUCHS
Prices include the recycling fee.
A high-temperature inductive sensor detects metal contactlessly in an environment whose temperature exceeds the capabilities of a standard design. It is used on heated fixtures, drying equipment and machines with thermally stressed mounting. The temperature of the entire connected assembly and the switching stability during the work cycle are decisive.
Browse sensors for high temperatures
The temperature of the conveyed part need not be the same as the temperature of the sensor. The head can be heated by radiation, hot air and heat conduction through a metal bracket. Therefore determine the temperature at the mounting location after the machine has stabilised and during the hottest part of the cycle. A measurement taken only at start-up may hide gradual heating.
| Part of the assembly | What to check |
|---|---|
| Sensing head and electronics | Permitted operating temperature and any separation of the head from the evaluation part. |
| Cable | Temperature range of the sheath, bending point and routing around hot surfaces. |
| Connector and mating connector | Range of both parts, sealing and the conditions stated for the prescribed connection. |
| Mounting bracket | Heat transfer into the body and the space needed for natural cooling. |
Distinguish between continuous operation, permitted short-term load and storage temperature. The storage figure does not permit switching while powered. At the same time, check the temperature limitation at the required output load; limit values from different catalogue lines cannot be combined automatically.
For the high-temperature series LR18X the manufacturer states an operating range of −25 to +120 °C, power supply 10–30 V DC and variants with cable or connector. The stated range belongs to this series. Before ordering, compare the complete order code, data sheet and parameters of the mating connector.
A change in temperature affects the electronics as well as the dimensions of the machine. Expansion of the bracket can shift the target relative to the active face, even though the sensor is operating within its permitted range. Do not set the gap right at the limit of the rated sensing distance Sn. Use the assured switching distance Sa stated for the given conditions and leave a mechanical reserve against contact.
Illustrative example: at the location is 95 °C. The head is suitable up to 120 °C, but the cable mating connector only up to 80 °C. The assembly as a whole is not suitable. The solution may be a suitable mating connector and lead, a change of connection position or a different sensor design. The figures illustrate the decision-making, they are not parameters of the lead shown.
A heat shield or a change of bracket may help, but confirm their benefit by measurement. The modification must not violate the required free space in front of the face or the rules for flush or non-flush mounting.
Yes, provided that the temperature of the sensor itself and all connected components remains within their permitted range. The temperature of the target alone does not determine the suitability of the assembly.
Only if the head, electronics, connector and other materials are also suitable. Changing the cable does not raise the temperature limit of the electronics.
Check the actual temperature, the shift of the target due to thermal expansion, the working gap reserve and the power supply. Replacing it with a higher temperature series will not by itself remove faulty mounting geometry.
Browse sensors for high temperatures
High-Pressure Sensors · All-Metal Sensors
For a specific selection, prepare the material and dimensions of the target, the working gap, the environmental conditions and the required electrical connection. An overview can be found in the categories Special sensors and Inductive sensors.
Technical documents: LANBAO: LANBAO LR18X, high-temperature series. This guide helps with selection; binding parameters, wiring and mounting are defined by the documentation of the ordered model.
We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.
Choose which cookies we may use. You can change your choice at any time.
They keep the cart contents, your login and selected language, and protect forms from abuse. An order cannot be completed without them, so they are used even without consent.
Google Analytics shows us traffic and behaviour on the website in aggregated form. This tells us which pages are not working for people. We do not identify anyone from this data.