−20 % DOSTĘPNY
TPU12x8BL, TECHNOLINE, polyurethane pneumatic tube, 12×8mm, blue

TPU12x8BL, TECHNOLINE, polyurethane pneumatic tube, 12×8mm, blue

Nr kat.: TPU12x8BL
Producent: TECHNOLINE
Dostępny 2772 szt.
Cena regularna bez VAT
1,13 €
z VAT
1,36 €
Nasza cena bez VAT
0,90 €
z VAT 21 %
1,09 €
Oszczędzasz
0,23 € bez VAT
Waga 0.07 kg
HS Code (Taric) 39173900
Kraj pochodzenia CN

Opis

TPU12x8BL, TECHNOLINE, polyurethane pneumatic tube, 12×8mm, blue

TPU12x8BL is a polyurethane tube in the TECHNOLINE range. With a diameter of 12×8mm and a wall of 2mm, the inner cross-section is 50.27mm². The fitting is selected according to outer diameter Ø12mm, not by the inner bore 8mm.

OD Ø12mmID Ø8mmWall 2mmblue

Technical parameters of the specific variant

Parameter Value
Order code TPU12x8BL
Manufacturer TECHNOLINE
Type straight PU tubes
Material polyurethane (PU)
Outer diameter (OD) 12mm
Inner diameter (ID) 8mm
Wall thickness (calculation) 2mm
Theoretical flow area (calculation) 50.27mm²
Colour blue

Pressures, operating limits and bends

Parameter Value
Nominal working pressure 10bar (1.0MPa)
Burst pressure 30bar (3.0MPa) – failure limit, not working pressure
Declared temperature range −20 to +60°C
Dependence of working pressure on temperature At higher temperatures, the permissible pressure may decrease. The value 10bar cannot automatically be applied to +60°C.
Minimum radius of the PU tube itself A separate material value is not documented for the specific compound; use the mounting recommendation for routing at the fitting below
Mounting radius of the line at a push-in fitting R ≥ 150mm for OD Ø12mm – recommendation for the connection section, not an independently documented minimum bend of the tube material
The working pressure 10bar may not apply up to +60°C: at higher temperatures a pressure reduction may be necessary. The burst pressure 30bar is not an operating limit. The weakest component of the pneumatic distribution is decisive.

What does a small bending radius mean?

Bending the tube into too sharp an arc can make its inner profile oval, increase pressure loss and gradually fatigue the wall. The flexibility of PU alone does not replace the catalogue minimum radius for the exact variant.

Practical guide to material and pneumatic distribution

Why polyurethane?

A polyurethane tube combines compliance for distribution with moving sections, flexible bending and generally good abrasion resistance. PU allows the line to be routed around machine components where a stiffer tube would complicate routing. However, its capabilities vary according to the material subtype, temperature and specific composition.

For this version TPU12x8BL: A larger inner bore can help reduce pressure losses in long or flow-intensive branches, but needs more space for bending and correspondingly larger fittings.

What affects the flow rate and cylinder response?

The inner diameter determines the geometric cross-section; the actual flow rate further depends on the line length, the flow coefficient of fittings and valves, the pressure differential and the compressibility of air. A doubled cross-section alone does not mean exactly double the actual flow rate.

Geometric calculation for TPU12x8BL: wall thickness = (12 − 8)/2 = 2mm. Theoretical cross-section A = π·8²/4 = 50.27mm². OD/ID ratio = 1.5. The calculation says nothing about pressure resistance.

Effect of temperature on working pressure

With higher temperature, the mechanical properties of PU and the permissible working pressure may change. When designing the line, respect the operating temperature and the lowest pressure limit of the whole assembly. The burst pressure cannot be used as the working pressure.

Line volume for this bore

One metre of tube with an inner diameter 8mm has a geometric volume of approximately 50.27ml. When a fast response of the pneumatic actuator is required, monitor the line length and the volume that needs to be pressurised or exhausted when the state changes. This is not a flow rate value or the volume of compressed air at operating pressure.

Difference from the next size variant

The same group also includes TPU10X8BL (Ø10×8mm). The geometric bore of this variant represents 1 times cross-section of the compared product. This is a purely dimensional comparison; the maximum pressure or the exact ratio of actual flow rates cannot be determined from the difference in cross-sections.

Colour blue makes it possible to visually distinguish this pneumatic branch from other routes in the equipment. However, the colour variant alone does not prove a different pressure rating or chemical resistance.

Suitable fittings from the TECHNOLINE e-shop

For size OD 12mm, you can choose from the following push-in fittings in the TECHNOLINE range. The matching outer diameter, tube material and working limit of the whole assembly are decisive.

Version Fitting code Link to e-shop
Straight push-in fitting TPU12 Show offer
Elbow fitting 90° TPV12 Show offer
T-connector TPE12 Show offer
Y-connector TPY12 Show offer

The cut must be square and clean. Insert the tube to the stop, mechanically verify retention and carry out a leak check on first pressurisation.

Need a transition to a different diameter? Category Reducing fittings contains various dimensional combinations; select according to the actual OD values of both tubes.

Specific questions about the product

Which dimension should be used to choose a fitting for TPU12x8BL?

By outer diameter Ø12mm. The Ø8mm bore is used to assess the geometric cross-section, not the size of the push-in opening.

How to verify the bend of tube TPU12x8BL?

For routing the tube at a Ø12mm push-in fitting, the recommended radius is R ≥ 150mm. This dimension is not the minimum radius of the tube itself.

Is the stated catalogue pressure safe for every temperature?

No. The value at 20°C is not automatically permissible at a higher temperature. The design must respect the temperature limitations of the exact material and the weakest element of the system.

Parametry techniczne

Objednací kódTPU12x8BL
VýrobceTECHNOLINE
Outer diameter12mm
Inner diameter8mm
ColourBlue

Zapytaj o produkt

Zapytaj nas o parametry techniczne, zgodność z Twoim urządzeniem, dostępność lub cenę przy większym zamówieniu. Pomoże, jeśli napiszesz, do jakiego zastosowania potrzebujesz produktu — jeśli nie będzie pasował, polecimy odpowiedniejszy typ.

Kód k opsání. Pokud ho nepřečtete, klikněte na Načíst nový kód.
Pytanie dotyczy produktu TPU12x8BL

Wysyłając, wyrażasz zgodę na przetwarzanie podanych danych w celu obsługi zapytania. Nie przekazujemy danych osobom trzecim.

Produkty powiązane

Pliki cookies na tej stronie

Techniczne pliki cookies są potrzebne do działania koszyka i zamówienia — są używane zawsze. Analityczne pliki cookies pokazują nam, których stron ludzie szukają i gdzie się gubią, i pomagają nam ulepszać sklep. Użyjemy ich tylko wtedy, gdy na to pozwolisz. Więcej w zasadach przetwarzania danych.