VBA11A-F02, SMC, air pressure booster up to 4×, thread G1/4
VBA11A-F02, SMC – pneumatic pressure booster; Pressure increase ratio: up to 4×; Connection thread: G1/4; Principle: pneumatic, without electrical power supply.
Kurs 24,39 Kč za 1 EUR. Ceny są orientacyjne, rozliczenie następuje w koronach czeskich.
SMC VBA series pneumatic boosters increase air pressure up to double without electrical energy. They help where the supply is not sufficient for the required cylinder force. Choose by required pressure, flow and tank size.
VBA11A-F02, SMC – pneumatic pressure booster; Pressure increase ratio: up to 4×; Connection thread: G1/4; Principle: pneumatic, without electrical power supply.
VBA40A-F04GN, SMC – pneumatic pressure booster; Pressure increase ratio: 2×; Connection: G1/2; GN accessories: 2 pressure gauges and silencer.
Ceny zawierają opłatę recyklingową.
A pneumatic booster increases the compressed air pressure for a selected branch of the machine. It is worth considering where a local task needs a higher pressure than the other consumers. Before selecting, however, separate the required pressure, the instantaneous flow and the frequency of working cycles. A higher reading on the pressure gauge without consumption does not by itself prove that the device can handle the production cycle.
This category includes VBA11A-F02 and VBA40A-F04GN. According to the SMC VBA catalogue VBA11A works with a pressure increase ratio of 2 to 4, while VBA40A works with a ratio of 2. For VBA11A, the inlet pressure range is 0.1–1 MPa and the outlet setting 0.2–2 MPa; these values are not interchangeable. The manufacturer specifies flow characteristics according to which the achievable outlet pressure drops as consumption increases. The standard version requires horizontal installation. When designing, follow the documentation of the exact order code.
The booster does not create energy for free: part of the supplied air is used for its drive. Therefore, make the operating comparison for the whole station and its actual working mode. Record the production time, idle time and the number of consumers working simultaneously. An occasional short stroke is a different requirement from a continuous consumption of the same peak flow.
Consider a consumer that, in the model, consumes 3 normal litres of air per cycle. Ten cycles per minute means an average consumption of 30 Nl/min. However, if the actual consumption lasts only half a second, it corresponds to a flow of 360 Nl/min during this part of the cycle. Both values are correct, but describe a different time level.
A tank can bridge a short peak, but it must have time to refill. Its volume cannot be determined from the difference of these flows alone: the calculation includes the permitted pressure drop, the actual inflow and the time sequence of consumption. The example is not a sizing of a specific VBA or a recommendation for a specific pressure vessel. It shows which data the process engineer should provide to the designer.
Prepare the measurement of the inlet and outlet pressure in the same time record. If the inlet drops at the same time, first look for a restriction upstream of the booster. If the inlet is stable and the outlet drops only during repeated working cycles, compare the load profile with the design. Supplement the result with the regulator setting, line lengths and the state of the air preparation.
Before opening the system, safely disconnect the supply and verify that all separated volumes are depressurised. Air may remain trapped behind a fitting or in the tank. For the downstream distribution, use air preparation and suitable pneumatic hoses, always within the limits of their specific version.
No. You also need the operating point under consumption and the consumption profile over time. Reaching the pressure with no load is not a test of performance in production.
No. It increases the available short-term reserve, but if consumption is higher than replenishment over a long period, the pressure will gradually drop.
Techniczne pliki cookies są potrzebne do działania koszyka i zamówienia — są używane zawsze. Analityczne pliki cookies pokazują nam, których stron ludzie szukają i gdzie się gubią, i pomagają nam ulepszać sklep. Użyjemy ich tylko wtedy, gdy na to pozwolisz. Więcej w zasadach przetwarzania danych.
Wybierz, których plików cookies możemy używać. Wybór możesz w każdej chwili zmienić.
Przechowują zawartość koszyka, logowanie i wybrany język oraz chronią formularze przed nadużyciem. Bez nich nie można złożyć zamówienia, dlatego są używane także bez zgody.
Usługa Google Analytics pokazuje nam ruch i zachowanie na stronie w formie zbiorczej. Dzięki temu wiemy, które strony nie działają dla ludzi. Na podstawie tych danych nikogo nie identyfikujemy.