TH0604B-20, SMC, FEP fluoropolymer tube 6/4 mm, black, roll 20 m
TH0604B-20 SMC – FEP fluoropolymer tube 6/4 mm, black, roll 20 m. The variant is intended for pneumatic distribution according to the stated dimensions and material.
Tipo de cambio 24,43 Kč por 1 EUR. Los precios son orientativos; la facturación se realiza en coronas checas.
Fluoropolymer FEP tubes resist chemicals and high temperatures and have a smooth inner surface. They are suitable for the food industry, chemicals and laboratories. Choose by diameter, pressure, temperature and medium.
TH0604B-20 SMC – FEP fluoropolymer tube 6/4 mm, black, roll 20 m. The variant is intended for pneumatic distribution according to the stated dimensions and material.
Los precios incluyen la tasa de reciclaje.
FEP is the designation of a fluoropolymer material. In the current listing, this category is represented by TH0604B-20 from SMC. Therefore, base the selection on the TH series documentation and the full order code. The name of the material group alone does not determine the permitted operation or the form of connection.
SMC TH table on page 726 assigns model TH0604 an outer diameter of 6 mm and an inner diameter of 4 mm. The letter B designates the black opaque version, the suffix 20 a roll length of 20 m. The manufacturer states fixed use for the series and does not permit it in places where the tube moves.
Draw the parts of the equipment that change position during operation. Easy manual bending does not prove suitability for repeated movement; such a mode must be explicitly permitted by the documentation of the selected version.
For TH0604 the manufacturer states maximum 1.5 MPa at 20 °C or less and 0.55 MPa at 100 °C. The usable limit of the assembly is determined by the lower permitted value of the tube or connection. The media table lists air, water and inert gas; do not assess another medium solely by the name FEP.
For your own specification, create an overview of operating states: cold start, normal operation, maximum temperature and cleaning. Assign pressure and medium to each. Assessing the whole table prevents a state that lasts briefly but is part of the regular working cycle from being overlooked during selection. Also state the measuring point and how the values were obtained, so that the specification can later be compared with reality.
If the machine documentation generally states a fluoropolymer, add the exact material designation. The compared Teflon tubes assess according to its own manufacturing sheet. Do not consider the same size or a similar colour as a basis for approving a replacement.
For our own tutorial model, let us choose a route with two straight sections of 120 mm each and one right-angle arc whose radius measured to the line axis is 50 mm. The arc length is π × 50 / 2 = approximately 78.5 mm. The whole geometric route therefore measures 120 + 78.5 + 120 = 318.5 mm.
This is design geometry with arbitrarily chosen inputs, not a prescribed radius or finished cutting length of a product. The calculation does not include insertion into fittings. Before cutting, compare the chosen bend with the documentation of the exact tube and add mounting lengths according to the connection drawing. When the supply position changes, recalculate the whole route.
Add support points, access to joints and the prescribed test procedure to the mounting plan. Select a tool for preparing the ends in the category Cutting pliers, knives only after verifying its suitability for the given material. Document the handover with a photo of the actual route.
As our own diagnostic procedure, in case of problems we recommend comparing actual operation with the specified table of states. Record where the problem appeared and whether it was preceded by heating, cleaning or intervention in the line. Then check the relevant section according to the manufacturer's instructions; simply increasing the clamping force or randomly changing the material is not a documented solution to the cause.
Attach the full code, a route sketch and a table of media, pressures and temperatures. Add the required quantity and packaging method.
You need the value at the actual temperature, the specified medium and the connection conditions. An overview of other material branches can be found in the category Pneumatic tubes.
Necesitamos las cookies técnicas para que funcionen el carrito y el pedido — se usan siempre. Las cookies analíticas nos muestran qué páginas buscan las personas y dónde se pierden, y nos ayudan a mejorar la tienda. Solo las usaremos si nos lo permites. Más información en la política de tratamiento de datos.
Elige qué cookies podemos usar. Puedes cambiar tu elección en cualquier momento.
Guardan el contenido del carrito, el inicio de sesión y el idioma elegido, y protegen los formularios frente a abusos. Sin ellas no se puede finalizar el pedido, por eso se utilizan incluso sin consentimiento.
Google Analytics nos muestra de forma agregada el tráfico y el comportamiento en el sitio. Así sabemos qué páginas no funcionan para los usuarios. Con estos datos no identificamos a nadie.