SCB22MP1PC1, EMAS, capacitive touch switch
SCB22MP1PC1 EMAS – capacitive touch push button, green, 10-30V DC, 22 mm, cable 1 m. Technical parameters, application, mounting and selection of the right variant.
Rate 24,43 CZK per 1 EUR. Prices are indicative, invoicing is in Czech crowns.
EMAS SCB capacitive touch switches without moving parts, wear-resistant. Choose by function (momentary or latching), supply and PNP/NPN output.
SCB22MP1PC1 EMAS – capacitive touch push button, green, 10-30V DC, 22 mm, cable 1 m. Technical parameters, application, mounting and selection of the right variant.
SCB22MP1NC1 EMAS – capacitive touch push button, green, 1 NC, 10-30V DC, 22 mm. Technical parameters, application, mounting and selection of the right variant.
SCB22MP1PSX EMAS – capacitive touch push button, green, 10-30V DC, 22 mm, M12. Technical parameters, application, mounting and selection of the right variant.
SCB22MP1NSX EMAS – capacitive touch push button, green, 10-30V DC, 22 mm, M12. Technical parameters, application, mounting and selection of the right variant.
SCB30MP7PC1 EMAS – capacitive touch push button, green, 10-30V DC, 30 mm, cable 1 m. Technical parameters, application, mounting and selection of the right variant.
SCB30MP7PSX EMAS – capacitive touch push button, green, 10-30V DC, 30 mm, M12. Technical parameters, application, mounting and selection of the right variant.
SCB30MP6PSX EMAS – capacitive touch push button, 12-30V DC, 30 mm, IP67, M12. Technical parameters, application, mounting and selection of the right variant.
SCB30MP6PC1 EMAS – capacitive touch push button, 12-30V DC, 30 mm, IP67, cable 1 m. Technical parameters, application, mounting and selection of the right variant.
Prices include the recycling fee.
Select a touch switch according to the data sheet of the specific code, not just according to the designation “touch”. That alone does not say what principle the element responds to, whether it holds the output state or how it connects to the control. This range includes EMAS SCB elements with cable or connector connection. For the models listed below, the manufacturer explicitly confirms the capacitive principle; this conclusion cannot be automatically extended to every other touch actuator.
SCB22MP1PC1 is a capacitive M22 version with momentary function, PNP-NO output, a one-metre cable and a 10–30 V DC supply. The data are confirmed by EMAS SCB22MP1PC1 technical sheet.
SCB30MP6PSX is designated Momentary, PNP-NO output, connection M12 and supply 12–30 V DC. The manufacturer also states a maximum load of 200 mA, a voltage drop below 2 V and a leakage current of at most 0.5 mA. See specification SCB30MP6PSX.
In contrast, SCB30MP7PSX is designated Stayput; it is also PNP-NO with M12 and a 12–30 V DC supply. The difference is confirmed by datasheet SCB30MP7PSX. Momentary and Stayput distinguish between momentary and maintained operating functions. However, the Stayput designation alone does not prove that the state is retained after the power supply is disconnected.
PNP and NPN represent different output circuits and require a corresponding control input. When replacing a mechanical push button, matching the meaning of NO is therefore not enough. Assess the sensor supply, common potentials, input current, detection levels and residual electrical quantities in both states. The maximum output current is not its normal own consumption, nor a guarantee of compatibility with every input below this value.
As a functionally different option, compare Non-illuminated push buttons. Mechanical position retention is provided by Latching push button switches; it cannot automatically be attributed the same signal behaviour as the electronic Stayput.
For an indicative check of the SCB30MP6PSX connection, consider a model input replaced by a resistance of 4.7 kΩ to the reference potential. At the limit leakage current of 0.5 mA, U = I × R = 0,0005 × 4700 = 2.35 V. If this model input guaranteed an inactive state up to 4 V, a simplified calculation would leave a reserve of 1.65 V.
The resistance and the 4 V limit are the author's assumptions, not parameters of a particular PLC. A real input may have a non-linear characteristic and filtering, so the calculation does not replace checking its documentation. In addition to the off state, the active level, line voltage drops and behaviour at power-up must be verified.
Follow the mounting drawing, the prescribed surroundings of the sensing surface and the connector version. At the specific workplace, practically verify the response with the gloves used, normal contamination and during cleaning. The declared ingress protection rating is not in itself a promise of the same sensitivity when wet, nor protection against unintentional activation.
No. The connector size does not determine a universal function of the contacts. The diagram of the specific product and the corresponding cable are decisive.
A normal touch function or protection of the electronics does not prove the safety properties of the whole command. Such a task requires a separate assessment and an appropriately documented solution.
We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.
Choose which cookies we may use. You can change your choice at any time.
They keep the cart contents, your login and selected language, and protect forms from abuse. An order cannot be completed without them, so they are used even without consent.
Google Analytics shows us traffic and behaviour on the website in aggregated form. This tells us which pages are not working for people. We do not identify anyone from this data.