TEAL-AW-AR3000, TECHNOLINE, Connecting spacer for AL-AW-AR 3000
TEAL-AW-AR3000 TECHNOLINE – Connecting spacer for AL-AW-AR 3000. The exact variant is determined by the manufacturer's order code.
Rate 24,43 CZK per 1 EUR. Prices are indicative, invoicing is in Czech crowns.
Connecting parts for assembling air preparation units – spacers, branch blocks and brackets. Choose by air preparation unit series.
TEAL-AW-AR3000 TECHNOLINE – Connecting spacer for AL-AW-AR 3000. The exact variant is determined by the manufacturer's order code.
TEAL-AW-AR2000 TECHNOLINE – Connecting spacer for AL-AW-AR 2000. The exact variant is determined by the manufacturer's order code.
TEAL-AW-AR1000 TECHNOLINE – Connecting spacer for AL-AW-AR 1000. The exact variant is determined by the manufacturer's order code.
C4SF, SMC, polycarbonate bowl for AF/AW40. It is a specific industrial component or accessory intended for the given product series.
AR23P-270AS SMC – mounting bracket for the AR20(K)-B series regulator. When selecting, verify the connection, size and other parameters of the specific variant.
Y400-D, SMC, spacer (connecting element). The mounting part is used for mechanical fixing or connection of a specific element.
E400-F04-D, SMC, female threaded end piece, axial thread. The mounting part is used for mechanical fixing or connection of a specific element.
Y400T-1-D, SMC, spacer with mounting bracket (connecting element), extended version. The mounting part is used for mechanical fixing or connection of a specific element.
Y410-F03-D, SMC, single branch tee (connecting element). It is a specific industrial component or accessory intended for the given product series.
C3SF, SMC, polycarbonate bowl for AF/AW30. It is a specific industrial component or accessory intended for the given product series.
Y44-F02-D, SMC, four-way branch, for modular air preparation units. It is a specific industrial component or accessory intended for the given product series.
AR40M-F0403-D, SMC, modular pressure regulators. The air preparation element filters, regulates or otherwise prepares the compressed air for the pneumatic system.
Prices include the recycling fee.
Connecting accessories of the air preparation unit address the mechanical seating and continuity of the individual modules. The same brand is not enough to confirm dimensional conformity. Compare the series, size, seals and mounting procedure of all connected parts.
| Step | What to document |
|---|---|
| Identification | series and size of both modules |
| Operating requirements | mounting and sealing parts |
| Acceptance | assembly and tightness of the joint |
Choose accessories according to the interface of the specific modules and the function of the joint. First, we recommend compiling a list of the full codes of the adjacent elements, drawing the flow direction and marking the fixing points. Only then choose spacers, branches and end pieces. This procedure helps prevent ordering a part that looks similar but whose purpose has not been verified for the designed assembly.
The SMC AC-D mounting drawing distinguishes the spacer, retaining parts, screws and seals. The bracket variant adds a fixing element. Tightness is ensured by a correctly assembled interface including the seal; the mere presence of screws does not confirm that the joint is complete. When designing, therefore, assess the pneumatic connection and the mechanical fixing as two related requirements.
The listing includes Y400-D, Y400T-1-D, E400-F04-D, Y410-F03-D and Y44-F02-D from SMC. TECHNOLINE has separate items TEAL-AW-AR1000, TEAL-AW-AR2000 and TEAL-AW-AR3000. To verify continuity, we recommend comparing the drawing of both mating parts, the seal number and the full version. An identical part of the designation is not by itself proof of interchangeability.
The AC-D manual requires residual pressure to be removed and the regulator setting to be released before dismantling. During assembly, the projection of the spacer must sit in the corresponding recess. The modules are aligned in a straight line and the screws are tightened evenly according to the value for the given size. After replacement, the function and external leakage are checked. The tightening torque of another thread or series is not a substitute for this instruction.
In the assembly sketch, we recommend adding the side space for tools and the vertical space needed to service the bowls. Separate dimensions from working clearances: the width of a component is not the same as the space needed to replace it. Also check the path of the removed part: the space below the bowl may be sufficient, but a side obstacle may prevent tool access. We recommend carrying out this check already in the assembly sketch. For each branch, note which preparation stages precede it and which consumers it will supply.
For a new branch, compile your own consumption table. Assess the common section according to simultaneity and a separate branch according to its working cycle. If you are adding another function, for example lubricator, go through the order of the whole assembly again. Keep a record of the full codes together with the drawing, so that a future replacement is based on the version actually used.
This is purely our own geometric model, not dimensions of SMC or TECHNOLINE products. Let us assume three modules with widths of 44, 58 and 46 mm. Two joints each add 6 mm; we choose an end clearance of 18 mm on each side. The total required width according to these assumptions is 44 + 58 + 46 + 2 × 6 + 2 × 18 = 196 mm.
In a panel 220 mm wide, 24 mm would remain. However, this result does not verify access to the bowls or the rear connection. For a specific assembly, we recommend checking in the drawing; the joint increment must not be added again if the manufacturer's overall dimension already includes it.
The AC-D manual mentions damage to the seal or loose retaining screws. After depressurising, check the assembly and follow the relevant mounting instructions.
For selection, require a documented modular interface, the corresponding size and the specific accessories. The external port and the interface between bodies are two separate parts of the design.
Primary source: SMC AC-D, mounting instructions and joint drawing.
We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.
Choose which cookies we may use. You can change your choice at any time.
They keep the cart contents, your login and selected language, and protect forms from abuse. An order cannot be completed without them, so they are used even without consent.
Google Analytics shows us traffic and behaviour on the website in aggregated form. This tells us which pages are not working for people. We do not identify anyone from this data.