G4-1052, RELPOL, retaining clip
G4-1052 RELPOL – retaining clip. Exact technical data for selecting the relay accessory type.
Rate 24,43 CZK per 1 EUR. Prices are indicative, invoicing is in Czech crowns.
Relay accessories – retaining clips, protection and indication modules, jumper combs and labels. Choose by relay and socket type.
G4-1052 RELPOL – retaining clip. Exact technical data for selecting the relay accessory type.
RS2.M00.AC, EMAS: plastic retaining clip designed for mechanically securing a compatible relay in a socket of series RS2.
GZT80-0040 RELPOL – retaining clip. Exact technical data for selecting the relay accessory type.
RS2.KY.01.DC EMAS – LED module with green LED and protective diode 6–24V DC. Key data: Value, RS2.KY.01.DC, LED module with protective diode. Exact technical data for selecting the relay accessory…
M91G, RELPOL, indication and protection module for relay coils, 6–24VAC/DC, green LED. Module M91G indicates coil energisation with a green LED and limits voltage peaks when it is switched off.
M93G RELPOL – protection module for relays. Key data: 230 V AC. Exact technical data for selecting the relay accessory type.
RS2.RC.05 EMAS – LED module with green LED and protective diode 110-230V AC. Key data: Value, RS2.RC.05, LED module with protective diode. Exact technical data for selecting the relay accessory type.
ZG20-1 RELPOL – jumper comb for relays. Key data: 20, 35A. Exact technical data for selecting the relay accessory type.
ZG20-3 RELPOL – jumper comb for relays. Key data: 20, 35A. Exact technical data for selecting the relay accessory type.
Prices include the recycling fee.
Choose relay accessories according to the task they are to perform in the assembly. A fixing part, a signalling module and an electrical jumper address different requirements. Therefore list each add-on separately in the assembly list, including its link to the relay or socket. This helps with initial fitting and when looking for a later replacement.
The range includes clips G4-1052 and GZT80-0040, modules M91G and M93G, combs ZG20-1 and ZG20-3 as well as EMAS add-ons RS2. Choose the base in the category Sockets. Verify the mechanical compatibility and voltage version of the add-on separately; the same brand alone does not replace a list of suitable combinations.
For each add-on, note the reason for use and the documentation that confirms it. Should it hold the inserted relay, indicate energisation, limit overvoltage or connect specified terminals? A single vague row “accessories” in the bill of materials does not distinguish these requirements and complicates acceptance of the assembly.
The RELPOL module table distinguishes diode, RC and varistor elements. M91G and M93G belong to the LV version with indication and a varistor for AC/DC. Do not automatically confuse them with a diode alone or an RC element; the diagram of the specific module is decisive.
For coil overvoltage suppression, OMRON warns also of prolonged relay drop-out. For a diode element for DC, polarity is essential. Therefore assess the addition of protection together with the control output and the timing requirement of the machine. A universal procedure of connecting one type of element to any coil is not correct documentation.
Use the indication as a separate observation in the service record. Alongside the state of the indicator, record the command from the control system and the actual response of the load. Their agreement or difference will help describe the fault. However, do not replace the words “all OK” in the acceptance report with the light alone.
Assume six identical model branches, each with a steady-state current of 0.08 A. With all branches operating simultaneously, the sum is 6 × 0.08 = 0.48 A. This is our own calculation example, not the current capacity of a comb, socket or other product offered.
In the brief for the common supply, also record any different switch-on moments and the maximum simultaneous operation. Transfer the sum to the point through which the common current actually flows. Branches after the split have different current conditions than the supply before the split. The result does not replace checking the permissible combinations or assessing the protection.
Interface data sheet PIR6W describes ZG20 as a jumper for common input or output signals. Before fitting, determine which terminals may be common. Use the comb colour together with the designation in the diagram; it does not by itself determine the electrical function of the connected circuit.
For the layout, prepare a list of the jumpered positions, their designations and the group boundaries. During future expansion, check whether the new branch belongs to the same circuit. Assess the space for the clip and module on the fitted assembly. Take instructions for fixing and electrical mounting from the documentation of the specific parts.
If a change in behaviour appears after adding a module, record the original and new fitting and the timing. Subsequent professional verification should compare both configurations with the documentation. Choose a replacement relay only after determining the cause, not just according to the indicator.
Its presence does not prove such protection. Assess the contact circuit and its protective devices separately.
No. The specific connection of the terminals, the equipment diagram and the permitted use of the jumper part are decisive.
We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.
Choose which cookies we may use. You can change your choice at any time.
They keep the cart contents, your login and selected language, and protect forms from abuse. An order cannot be completed without them, so they are used even without consent.
Google Analytics shows us traffic and behaviour on the website in aggregated form. This tells us which pages are not working for people. We do not identify anyone from this data.