LR6.5QBN04DPCY-E1, EMAS, inductive sensor, 6.5 mm, 4 mm, connector M8/3, NC
LR6.5QBN04DPCY-E1 EMAS – inductive sensor, 6.5mm, 4mm, PNP, NC, connector M8/3 pins. For industrial automation and non-contact metal detection.
Rate 24,43 CZK per 1 EUR. Prices are indicative, invoicing is in Czech crowns.
Inductive sensors detect metal objects without mechanical contact, so they do not wear and last for tens of millions of cycles. You will find cylindrical versions with threads from M5 to M30 as well as block-shaped sensors for profile mounting. They come in flush versions for alignment with a metal surface and in non-flush versions with a longer switching distance. You can choose by PNP or NPN output, normally open or normally closed contact, IP67 to IP69K protection rating, and connection by fixed cable or M8 and M12 connector. For aluminium, brass and copper, factor 1 sensors are available, which have the same switching distance as on steel. We supply sensors from Lanbao, TECHNOLINE, SICK, Balluff, IPF, IFM, EMAS and other brands. If needed, contact us and we will be happy to help you choose the right type for your application.
LR6.5QBN04DPCY-E1 EMAS – inductive sensor, 6.5mm, 4mm, PNP, NC, connector M8/3 pins. For industrial automation and non-contact metal detection.
LE40SZSF15DNO-E2 – LANBAO rectangular inductive sensor. 40x40x66mm, Sn 15 mm, NPN, NO. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40SZSF15DNC-E2 – LANBAO rectangular inductive sensor. 40x40x66mm, Sn 15 mm, NPN, NC. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40SZSF15DNR-E2 – LANBAO rectangular inductive sensor. 40x40x66mm, Sn 15 mm, NPN, NO and NC. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40SZSF15DPO-E2 – LANBAO rectangular inductive sensor. 40x40x66mm, Sn 15 mm, PNP, NO. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40SZSF15DPC-E2 – LANBAO rectangular inductive sensor. 40x40x66mm, Sn 15 mm, PNP, NC. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40SZSN20DNO-E2 – LANBAO rectangular inductive sensor. 40x40x66mm, Sn 20 mm, NPN, NO. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40SZSN20DNC-E2 – LANBAO rectangular inductive sensor. 40x40x66mm, Sn 20 mm, NPN, NC. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40SZSN20DNR-E2 – LANBAO rectangular inductive sensor. 40x40x66mm, Sn 20 mm, NPN, NO and NC. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40SZSN20DPO-E2 – LANBAO rectangular inductive sensor. 40x40x66mm, Sn 20 mm, PNP, NO. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40SZSN20DPC-E2 – LANBAO rectangular inductive sensor. 40x40x66mm, Sn 20 mm, PNP, NC. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40XZSF15DNO-D – LANBAO rectangular inductive sensor. 40x40x140mm, Sn 15 mm, NPN, NO, screw terminals. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40XZSF15DNC-D – LANBAO rectangular inductive sensor. 40x40x140mm, Sn 15 mm, NPN, NC, screw terminals. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40XZSF15DNR-D – LANBAO rectangular inductive sensor. 40x40x140mm, Sn 15 mm, NPN, NO and NC. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40XZSF15DPC-D – LANBAO rectangular inductive sensor. 40x40x140mm, Sn 15 mm, PNP, NC, screw terminals. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40XZSN20DNO-D – LANBAO rectangular inductive sensor. 40x40x140mm, Sn 20 mm, NPN, NO, screw terminals. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40XZSN20DNC-D – LANBAO rectangular inductive sensor. 40x40x140mm, Sn 20 mm, NPN, NC, screw terminals. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40XZSN20DNR-D – LANBAO rectangular inductive sensor. 40x40x140mm, Sn 20 mm, NPN, NO and NC. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40XZSN20DPC-D – LANBAO rectangular inductive sensor. 40x40x140mm, Sn 20 mm, PNP, NC, screw terminals. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40XZSF15DNO-E2 – LANBAO rectangular inductive sensor. 40x40x129mm, Sn 15 mm, NPN, NO, connector M12/4 pins. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40XZSF15DNC-E2 – LANBAO rectangular inductive sensor. 40x40x129mm, Sn 15 mm, NPN, NC, connector M12/4 pins. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40XZSF15DNR-E2 – LANBAO rectangular inductive sensor. 40x40x129mm, Sn 15 mm, NPN, NO and NC. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40XZSF15DPC-E2 – LANBAO rectangular inductive sensor. 40x40x129mm, Sn 15 mm, PNP, NC, connector M12/4 pins. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40XZSN20DNO-E2 – LANBAO rectangular inductive sensor. 40x40x129mm, Sn 20 mm, NPN, NO, connector M12/4 pins. Delivery on request from Technoline – datasheet, technical support, invoice.
LE40XZSN20DNC-E2 – LANBAO rectangular inductive sensor. 40x40x129mm, Sn 20 mm, NPN, NC, connector M12/4 pins. Delivery on request from Technoline – datasheet, technical support, invoice.
Prices include the recycling fee.
Inductive sensors are used for non-contact detection of metal objects in machines, production lines and industrial automation. In the TECHNOLINE range, you will find cylindrical and rectangular inductive sensors, M8, M12, M18 and M30 versions, PNP and NPN outputs, NO and NC functions, flush and non-flush variants, and sensors with a cable or connector.
When selecting an inductive sensor, compare above all the sensing distance Sn, housing size, flush or non-flush mounting, PNP/NPN, NO/NC, supply voltage and connection type. For special applications, all-metal, analogue, two-wire, high-temperature, high-pressure and Factor 1 inductive sensors are also available.
How to choose an inductive sensor | M8 / M12 / M18 / M30 | Flush / non-flush | PNP / NPN | Cables and connectors | Connecting to a PLC | FAQ
The right inductive sensor must match not only the required sensing distance, but also the material of the detected object, the machine design and the electrical wiring. When selecting, we recommend proceeding in this order:
Always confirm the final choice using the current data sheet of the specific model.
An inductive sensor is a non-contact electronic sensor for detecting metal objects. The active part of the sensor generates a high-frequency electromagnetic field. When a metal object approaches, eddy currents are induced in the material, which affect the sensor's oscillator. The evaluation electronics then change the state of the switching or analogue output.
Because the sensor does not need mechanical contact with the detected object, it is suitable for automation, position monitoring, end positions of mechanisms, counting metal parts, checking the presence of components and other industrial applications.
The most common cylindrical versions include inductive sensors with M8, M12, M18 and M30 threads. The size of the sensor affects the mounting options, mechanical robustness and usually also the achievable sensing distance.
View LANBAO cylindrical inductive sensors
A flush inductive sensor can, according to its specification, be mounted so that the active part is surrounded by metal. It is suitable, for example, for mounting in metal brackets or machine parts.
A non-flush inductive sensor needs free space around the active part. It often offers a longer sensing distance, but incorrect embedding in metal can significantly affect its function.
| Property | Flush | Non-flush |
|---|---|---|
| Mounting | Can be embedded according to the manufacturer's specification | Requires a free zone around the active part |
| Sensing distance | Usually shorter | Often longer |
| Typical mistake | Incorrect geometry of the metal bracket | Embedding the active head in metal |
The value Sn is the nominal sensing distance. It should not automatically be considered a guaranteed operating distance in every application. The actual function is affected by the material and size of the target, mounting, temperature, manufacturing tolerances and metal objects in the vicinity.
For a reliable design, leave a sufficient margin and verify the operating distance using the data sheet of the specific sensor.
A standard inductive sensor may not have the same sensing distance for steel, stainless steel, aluminium, brass or copper. If different metal materials alternate in the application, an inductive sensor with correction factor 1 may be suitable.
View Factor 1 inductive sensors
For DC inductive sensors, the type of transistor output is one of the most important parameters.
A PNP inductive sensor typically supplies a positive potential to the output when activated. An NPN inductive sensor typically pulls the output towards 0 V when activated. The correct variant must match the wiring of the digital input of the PLC or other device.
| Output | Typical behaviour when switched | Check when selecting |
|---|---|---|
| PNP | The output supplies a positive potential | Type and wiring of the PLC input |
| NPN | The output pulls the signal to 0 V | Type and wiring of the PLC input |
Matching the size, thread and sensing distance alone is therefore not enough when replacing an old sensor. Always also check PNP/NPN, NO/NC, the power supply and the connector pinout.
NO (Normally Open) is usually inactive without a detected target and switches the output to the active state upon detection.
NC (Normally Closed) works the opposite way – in the rest state the output is active and changes state when a metal object is detected.
Some four-wire inductive sensors provide both NO and NC outputs at the same time. The selection must match the required control logic and the PLC wiring.
Inductive sensors can be supplied with a permanently attached cable or with an industrial connector. The connector version makes mounting easier and allows the sensor to be replaced without replacing the entire cable run.
When selecting a cable, it is not enough to look only at the connector size. It is also necessary to check the number of pins, the connector gender, straight or angled version and the specific pinout of the sensor.
Cables and connectors for inductive sensors
Important: in some variants, for example, the NC output may be on a different pin than the NO output. Therefore, always check the wiring of the specific sensor before ordering a cable.
When connecting an inductive sensor to a PLC, first check the supply voltage and the output type. It is not enough that the LED indicator on the sensor responds. The signal must also be correctly fed to the digital input of the PLC.
The sensor LED confirms the state of the sensor electronics, but does not by itself confirm that the signal has actually reached the PLC program.
When counting products, gear teeth, revolutions or fast-moving mechanisms, the switching frequency of the inductive sensor is also important. The pulse must be long enough not only for the sensor itself, but also for the input electronics and the PLC filter.
For fast applications, check the minimum pulse length, the maximum frequency of the sensor and the parameters of the PLC digital input. If necessary, use a fast input or a hardware counter.
Other design variants of inductive sensors are available for special operating conditions.
Cylindrical inductive sensors with an M8, M12, M18 or M30 thread allow simple mechanical adjustment of the distance using nuts and are among the most common versions in industrial automation.
Rectangular inductive sensors can be advantageous where the machine design does not allow a cylindrical housing or where a different active surface size and mounting method are required.
LANBAO cylindrical inductive sensors
A mechanically similar sensor may not be electrically or functionally compatible. When looking for a replacement, compare at least:
| Problem | What to check |
|---|---|
| The sensor LED does not light up | Power supply, polarity, distance and target material |
| The LED responds, but the PLC does not | PNP/NPN, NO/NC, pinout, cable, common potential and PLC input |
| The sensor is permanently switched on | Surrounding metal, metal chips, mounting and a possible short circuit |
| The sensor occasionally misses | Sensing distance margin, vibration, target size, speed and PLC filter |
| It does not work after replacement | PNP/NPN, NO/NC, voltage, pinout and compatibility of the new type |
TECHNOLINE offers inductive sensors for standard and special industrial automation applications. For individual products, always check the specific technical parameters, availability, connection method and data sheet.
LANBAO cylindrical sensors | Factor 1 | Analogue | Two-wire | High-pressure | High-temperature
For training, application design and a practical understanding of how inductive sensors work, you can also use the TECHNOLINE / LANBAO training program. It covers the principle of inductive detection, sensor selection, PNP/NPN, NO/NC, mounting and connection to a PLC.
Training program – inductive sensors
An inductive sensor is a non-contact electronic sensor designed primarily for detecting metal objects. It detects a change in the electromagnetic field caused by an approaching metal.
Inductive sensors are used primarily for detecting metals. The actual sensing distance may depend on the type of metal, the size and shape of the target and the specific design of the sensor.
When activated, a PNP output typically supplies a positive potential, while an NPN output typically pulls the signal towards 0 V. The correct type must match the input wiring of the PLC or control system.
NO is usually inactive without a detected target and switches on upon detection. NC works the opposite way. Some four-wire inductive sensors provide both outputs.
Flush refers to an embeddable version that, according to the specification, can be mounted with metal around the active part. Non-flush refers to a non-embeddable version that needs free space around the active head.
Choose the size according to the available space, the required sensing distance, mechanical robustness and mounting method. M8 is compact, M12 is very universal, and M18 or M30 are used where a larger and more robust version is appropriate.
Sn is the nominal sensing distance. To design a reliable application, it is necessary to take into account the operating range stated by the manufacturer, the target material, mounting, mechanical tolerances and operating conditions.
Check the connector size, number of pins, connector gender, straight or angled version and, above all, the pinout of the specific sensor. The same connector size does not automatically mean the same electrical wiring.
Different metals affect the electromagnetic field in different ways. Therefore, a standard inductive sensor may have a different effective sensing distance for steel, stainless steel, aluminium, brass or copper. For applications with different metals, Factor 1 sensors can be considered.
When selecting, start with the sensor size and the required sensing distance. Then choose a flush or non-flush version, PNP/NPN output, NO/NC function and connection method. For a sensor with a connector, do not forget to order the matching cable.
View all inductive sensors | Cables and connectors for sensors
Technical note: The information provided is for guidance when selecting. Always verify the wiring, limit values, sensing distance, operating conditions and other technical parameters using the current data sheet of the specific product.
We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.
Choose which cookies we may use. You can change your choice at any time.
They keep the cart contents, your login and selected language, and protect forms from abuse. An order cannot be completed without them, so they are used even without consent.
Google Analytics shows us traffic and behaviour on the website in aggregated form. This tells us which pages are not working for people. We do not identify anyone from this data.