AN40-04, SMC, pneumatic exhaust silencer, thread R1/2, body size 40
AN40-04, SMC: pneumatic exhaust silencer. thread R1/2, body size 40. Use in pneumatic distribution and verified mounting criteria.
Rate 24,43 CZK per 1 EUR. Prices are indicative, invoicing is in Czech crowns.
Silencers for pneumatic valve exhausts reduce the noise of escaping air. Choose by thread and flow.
AN40-04, SMC: pneumatic exhaust silencer. thread R1/2, body size 40. Use in pneumatic distribution and verified mounting criteria.
ANA1-04, SMC: pneumatic exhaust silencer. thread R1/2, body size 1. Use in pneumatic distribution and verified mounting criteria.
AN500-06, SMC: pneumatic exhaust silencer. thread R3/4, body size 500. Use in pneumatic distribution and verified mounting criteria.
ANA1-06, SMC: pneumatic exhaust silencer. thread R3/4, body size 1. Use in pneumatic distribution and verified mounting criteria.
ANA1-10, SMC: pneumatic exhaust silencer. thread R1, body size 1. Use in pneumatic distribution and verified mounting criteria.
RBC0806, SMC: shock absorber. nominal size Ø8mm and stroke 6mm. Use in pneumatic distribution and verified mounting criteria.
AN800-14, SMC: pneumatic exhaust silencer. thread R1½, body size 800, catalogue flow rate max. 50m³/min (ANR) at 0.5MPa. Use in pneumatic distribution and verified mounting criteria.
YSR-16-20-C, Festo: self-adjusting shock absorber. stroke 20mm, energy 30J/zdvih. Use in pneumatic distribution and verified mounting criteria.
Prices include the recycling fee.
The listing includes the designations TBSL, TBSLM, TBESL and SMC AN, ANA1 or ANB1. When designing, start with the specific exhaust point: a single valve has a different requirement than the common exhaust of several branches working simultaneously.
The ANA1 and ANB1 series have sound-absorbing material and the manufacturer distinguishes them by connection and flow characteristics. Therefore assess the silencer simultaneously in terms of noise and exhaust resistance. The noise reduction value alone is not enough to decide whether the given version will suit your cycle.
Compare, for example, the range AN110-01 a ANB1-C10. SMC AN document distinguishes threaded and push-in variants. Check the connection letter and the full code in the model table; the general silencer designation does not by itself determine the interface.
The manufacturer's graphs ANA1/ANB1 are for the initial state. For the noise comparison, they state a supply pressure of 0.5 MPa and a measuring point one metre diagonally in front of the source at an angle of 45 degrees. The result from this arrangement is not automatically the resulting noise level of the whole production room.
SMC mounting instructions distinguishes plastic body, sintered metal and other metal bodies. Do not use a pipe wrench or pliers on plastic or sintered parts. For versions with specified flats, use the appropriate spanner. Do not transfer the instruction for additional turning of a plastic thread to other materials and designs.
Clogging can increase exhaust resistance and impair the function of the pneumatic circuit. SMC requires replacement before the circuit is affected and verification of the absence of residual pressure before replacement. For these products, the whole silencer is replaced; do not replace the absorbing filling alone. Monitor changes in actuator operation together with changes in sound.
For diagnostics, we recommend our own simple protocol: record the stroke time, the pressure on the exhaust branch during the same cycle and the designation of the fitted silencer. Compare the record with the measurement after professional replacement with a corresponding new piece. Always change one condition so that the result can be evaluated. Record noise at the same place with the same number of simultaneously working branches. For a common exhaust, draw the order of their switching in the protocol. Otherwise, a different operating state may outweigh the benefit of replacement and the comparison of two measurements will be misleading. Motion adjustment is also related to the category Flow control valves.
The following numbers are purely model values, not parameters of the offered silencers. Imagine two independent sources at the same measuring point: the exhaust with a level of 98 dB and the rest of the machine operation with a level of 76 dB. Let us assume that a hypothetical measure reduces only the exhaust contribution by 28 dB, i.e. to 70 dB, while the rest of the operation remains the same.
The logarithmic sum after the modification is 10 × log10(10^(70/10) + 10^(76/10)) ≈ 77.0 dB. Before the modification, it is similarly approximately 98.0 dB. The total reduction is therefore about 21 dB, even though we reduced the exhaust alone by twenty-eight in the model. The second source became decisive. The calculation assumes comparable measurements and uncorrelated contributions; it does not replace measurement of the actual machine.
In the report, also evaluate the cycle time. A quieter sound without a comparable working result does not by itself prove a successful solution.
Such a design exists: Pneuflex BESL uses an adjusting screw and securing of its position. However, verify this function for the specific version; it does not follow from the general silencer designation.
We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.
Choose which cookies we may use. You can change your choice at any time.
They keep the cart contents, your login and selected language, and protect forms from abuse. An order cannot be completed without them, so they are used even without consent.
Google Analytics shows us traffic and behaviour on the website in aggregated form. This tells us which pages are not working for people. We do not identify anyone from this data.