Limit Switches
A limit switch converts the reaching of a certain position into electrical information. In the mechanical version, a moving part of the machine acts on a plunger, roller, lever or other actuator. The magnetic door version, on the other hand, works with a matching counterpart without mechanical pressing. The right selection begins with a description of the movement and the meaning of the signal: do you need to confirm a position, start the next process step, or create part of a safety function? These tasks may require different solutions, even if the mounting location looks similar at first glance.
Eight branches according to the actual way of use
- Safety Limit Switches include key-operated, hinge and rope-pull designs. The selection must follow the risk assessment, the actuation method and the evaluation of the entire safety circuit.
- Plastic Limit Switches IP65 offer the EMAS L5 series with various heads. A plastic housing does not mean that the roller or lever must be made of the same material.
- Metal Limit Switches IP65 are intended for selecting a metal mechanical assembly. Besides the housing, compare the head, cable gland, approach space and electrical function.
- Cross Limit Switches include EMAS CSM02, CSM04 and CSM10. The decisive factor is the switching sequence during rotation, not just the number of visible arms.
- Miniature Limit Switches include, for example, the MK1 and MN1. series Small dimensions require careful checking of travel, connection method and terminal protection.
- Limit Switches with Higher IP67 Protection contain metal models L61. The assessment of the environment must also include the cable, its termination and the actual cleaning method.
- Magnetic Sensors in this branch are EMAS SM door components. They are not automatically the same product as a sensor inserted into the slot of a pneumatic cylinder.
- Limit Switch Spare Parts make it possible to address a specific head or contact block. Compatibility is determined by order codes and assembly documentation, not by similarity of photos.
From machine movement to choice of head
A direct plunger requires correct guidance of force; a lateral approach outside the specified direction may stress the mechanism differently than the design assumes. A roller works with a ramp surface whose shape determines the course of pressing and release. With a lever, also assess the length setting and the space during the return movement. A flexible whisker is not a substitute for any position tolerance: it still has defined directions and limits of actuation.
According to EMAS, the specific L5K13MEM123 has a plastic body, an adjustable lever with a metal roller of 18 mm and snap-action contacts 1NO + 1NC. It is an example of why the housing and actuator materials are assessed separately. See technical sheet L5K13MEM123.
Snap action is not positive opening
A snap-action mechanism changes the contact state abruptly once a certain actuator position is reached. Slow action, by contrast, follows the actuator movement more closely. Neither name by itself proves positive opening. That is a documented design feature in which the mechanical force of the actuator directly separates the contacts under specified conditions. The principle and the significance of the required travel or force are explained by OMRON in its direct opening overview.
Read the NO and NC designations relative to the reference state shown in the diagram. The number of contacts does not say whether the paths are electrically separated, what their timing is or how they should be evaluated. A current rating must be linked to the voltage and utilisation category; it does not guarantee universal switching of motors. For a small control signal, on the other hand, check the minimum load conditions, not just the maximum current.
Travel, overtravel and repeatability
The travel to switching, the further permitted movement after switching and the difference between the switching and release positions describe different parts of the operating cycle. Repeatability, by contrast, expresses the scatter of the achieved switching position on repetition; it is neither the total travel nor the stopping accuracy of the whole machine. This meaning is defined by the OMRON terminology overview.
The switch is not meant to replace a fixed end stop of the drive. The mechanics must allow it to be actuated correctly even with tolerances, inertia and wear. After the switching point is reached, you need a controlled reserve, but you must not exceed the permitted operating range. The drawing or switching diagram of the specific model is more important for this step than a general description of the series.
Model example: why a signal does not mean an immediate stop
Consider ordinary position signalling of a carriage at a speed of 0.20 m/s. The model delay between the input change and the start of braking is 0.05 s, so the carriage travels 0.20 × 0.05 = 0.010 m during this time, i.e. 10 mm. With subsequent constant deceleration of 1 m/s², the further distance is v² / (2a) = 20 mm. The total model stopping distance is 30 mm.
The figures are not parameters of any listed switch, nor a calculation of a safe distance. They only show why the stopping position cannot be derived from the moment of switching alone. A real design involves further tolerances, variable load, control response and verified braking. The actuator overtravel is calculated from the specific approach geometry, not by simply taking over the carriage travel.
Mounting and FAQ
Check the strength of the bracket, the head position, the approach from both required directions, cable strain relief and sealing of the connection. The degree of protection applies under the manufacturer's conditions; one protected part does not prove the protection of the whole installation. After adjustment, test the slowest and fastest working movement and the return to rest.
Record the switching and release positions, the approach direction used and the test speed in the report. Without these conditions, two seemingly different measurements may only describe a different operating cycle, not a faulty switch.
Does an NC contact guarantee a safety function?
No. A normally closed contact is only one property of the component. The required safety must be demonstrated by the design and verification of the entire function.
Can a replacement head change the purpose of the switch?
Only within an assembly supported by the manufacturer and after the function has been verified again. A change of geometry may shift the switching point, the actuation direction and the available travel reserve.