Phone +420 774 723 123 Cart · 0 · empty

Pneumatic accessories

SMC, Pneuflex and other pneumatic accessories – push-in fittings, threaded fittings, reducers, flow control valves, silencers, plugs, blow guns and suction cups. Choose by tube diameter and connection thread.

Subcategories

Filters
Found 696 products

KQ2L06-00A, SMC, elbow fitting 90°, 2× tube Ø6mm

Cat. no.: KQ2L06-00A

KQ2L06-00A, SMC, elbow fitting 90°, 2× tube Ø6mm. Change of line direction by 90° without a sharp tube bend right at the joint.

On request
2,37 €
excl. VAT · 2,87 € incl. VAT
OUR TIP

AN120-M5, SMC, pneumatic exhaust silencer, thread M5, body size 120

Cat. no.: AN120-M5

AN120-M5, SMC: pneumatic exhaust silencer. thread M5, body size 120. Use in pneumatic distribution and verified mounting criteria.

On request
2,46 €
excl. VAT · 2,97 € incl. VAT

KQ2N04-06, SMC, plug-in connecting stem, stem reducer Ø4mm↔Ø6mm

Cat. no.: KQ2N04-06

KQ2N04-06, SMC, plug-in connecting stem, stem reducer Ø4mm↔Ø6mm. A plug-in connecting stem connecting existing push-in fittings, not loose tubes.

On request
2,46 €
excl. VAT · 2,97 € incl. VAT

KQ2S04-M3G, SMC, straight fitting with internal hexagon, tube Ø4mm, male M3

Cat. no.: KQ2S04-M3G

KQ2S04-M3G, SMC, straight fitting with internal hexagon, tube Ø4mm, male M3. Straight connection of the tube to threaded port M3; the thread seal must be verified.

On request
2,46 €
excl. VAT · 2,97 € incl. VAT

KQ2S04-M6A, SMC, straight fitting with internal hexagon, tube Ø4mm, male M6

Cat. no.: KQ2S04-M6A

KQ2S04-M6A, SMC, straight fitting with internal hexagon, tube Ø4mm, male M6. Straight connection of the tube to threaded port M6; the thread seal must be verified.

On request
2,46 €
excl. VAT · 2,97 € incl. VAT

KQ2S06-M5A, SMC, straight fitting with internal hexagon, tube Ø6mm, male M5

Cat. no.: KQ2S06-M5A

KQ2S06-M5A, SMC, straight fitting with internal hexagon, tube Ø6mm, male M5. Straight connection of the tube to threaded port M5; the thread seal must be verified.

On request
2,46 €
excl. VAT · 2,97 € incl. VAT
OUR TIP

TBPE04, TECHNOLINE, all-metal T-connector for Ø4mm tube

Cat. no.: TBPE04

TBPE04, TECHNOLINE, all-metal T-connector for Ø4mm tube. Branching into three pneumatic branches; the flow is divided according to consumption and line resistance. Metal body.

On request
2,48 €
excl. VAT · 3,00 € incl. VAT

KQ2L04-M3G, SMC, elbow push-in fitting 90°, tube Ø4mm, thread M3

Cat. no.: KQ2L04-M3G

KQ2L04-M3G, SMC: elbow push-in fitting 90°; tube Ø4mm, thread M3. Dimensions and use according to the catalogue series.

On request
2,54 €
excl. VAT · 3,07 € incl. VAT

KQ2L04-06A, SMC, elbow reducing adapter 90°, tube Ø4mm / plug-in stem Ø6mm

Cat. no.: KQ2L04-06A

KQ2L04-06A, SMC, elbow reducing adapter 90°, tube Ø4mm / plug-in stem Ø6mm. Elbow reducer 90°: push-in tube Ø4mm, plug-in stem Ø6mm into the counterpart.

On request
2,58 €
excl. VAT · 3,12 € incl. VAT

KQ2S06-01AS, SMC, straight fitting with internal hexagon, tube Ø6mm, male R1/8

Cat. no.: KQ2S06-01AS

KQ2S06-01AS, SMC, straight fitting with internal hexagon, tube Ø6mm, male R1/8. Straight connection of the tube to threaded port R1/8; with pre-applied thread seal.

On request
2,58 €
excl. VAT · 3,12 € incl. VAT

KQ2N06-08, SMC, plug-in connecting stem, stem reducer Ø6mm↔Ø8mm

Cat. no.: KQ2N06-08

KQ2N06-08, SMC, plug-in connecting stem, stem reducer Ø6mm↔Ø8mm. A plug-in connecting stem connecting existing push-in fittings, not loose tubes.

On request
2,66 €
excl. VAT · 3,22 € incl. VAT
OUR TIP

KQ2H06-02AS, SMC, straight fitting, tube Ø6mm, male R1/4

Cat. no.: KQ2H06-02AS

KQ2H06-02AS, SMC, straight fitting, tube Ø6mm, male R1/4. Straight connection of the tube to threaded port R1/4; with pre-applied thread seal.

On request
2,66 €
excl. VAT · 3,22 € incl. VAT

Prices include the recycling fee.

Pneumatic accessories

Pneumatic accessories connect individual parts of the air circuit and help adapt its arrangement to a specific machine. When selecting, you need to know not only the part designation, but also both connected counterparts, the required function and operating conditions. A similar appearance of fittings or the same brand do not by themselves confirm interchangeability. This category is a signpost for line design, air distribution, flow adjustment and vacuum gripping.

Select the branch according to the task in the circuit

  • Threaded fitting: connection to a specific threaded port of the equipment.
  • Push-in fittings: selecting a connection for the corresponding pipe or tube.
  • Bulkhead fittings: passing the line through a panel with resolved fixing.
  • Reducing fittings: connecting different connection sizes.
  • Flow control valves: flow adjustment taking into account the direction and function of the valve.
  • Silencers: exhaust accessories, which are also selected according to flow requirements.
  • Blanking plugs: closing the connection with a corresponding version.
  • Blow gun: manual work with air according to the rules of the given workplace.
  • Pneumatic suction cups: contact of the vacuum gripper with the surface of the handled part.

Three checks before ordering

Mechanical interface: record the full connection designation on both sides. For the tube, distinguish the outer and inner diameter; for the thread, its type, size and sealing method. Also check the space for mounting and service; the correct part may not be suitable for an installation that is too tight.

Function: draw where the medium should flow from and to. Connecting, branching, blanking, throttling and gripping are different tasks. For more complex accessories, compare the diagram and the full order code, not just the first part of the name.

Operating conditions: verify the permissible medium, pressure, temperature and environment for the specific version in the manufacturer's documentation. Assess use in vacuum separately. Do not derive the permitted range of the whole assembly from a parameter of one of its elements.

Model list of connection points

Let us consider four workstations, each with two separate lines. If each line forms one uninterrupted section, eight sections have a total of sixteen ends to connect. Dividing all eight sections into two parts adds eight intermediate fittings and sixteen more tube ends. This is our own inventory example, not a calculation of pressure loss or probability of leakage. It helps reveal missing counterparts and distinguish a spare piece from a part actually needed in the assembly.

Mounting and troubleshooting

Before intervention, shut down the equipment according to its instructions and secure it against unexpected movement. Disconnect lines only after safely removing pressure; for vacuum gripping, first secure the transported object. Take the mounting procedure, tightening and insertion check from the instructions of the specific accessory. After assembly, verify tightness, actual function and maintenance access during controlled commissioning.

In case of a leak, first determine its location, then check the counterpart, line size, seal condition and mechanical stress on the joint. In case of slow movement, monitor the whole supply and exhaust. Random replacement of one part without verifying the cause can leave the original problem in another part of the circuit.

FAQ

Can I replace a fitting based on a photo?

A photo helps determine the shape. For ordering, however, add dimensions, exact connection, function and operating limitations. For a replacement, record the original code and also compare the counterpart.

How to prepare documentation for selecting accessories?

Attach a simple circuit diagram, a list of connections, tube sizes and operating conditions. Mark what you already have and what should be part of the delivery; this makes the list and the compatibility check more precise.

Cookies on this website

We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.