Phone +420 774 723 123 Cart · 0 · empty

Draw-Wire Incremental Encoders

Draw-wire position sensors for measuring linear travel of up to several metres using a wound wire. Choose by measuring range and output (incremental, potentiometric, analogue).

Filters
Found 1 products

LS501-10P/1250/R5k L0.25%/KB, LARM, draw-wire encoder, IP65

Cat. no.: LS501-10P/1250/R5k L0,25%/KB

LS501-10P/1250/R5k L0.25%/KB, LARM, draw-wire encoder, IP65. Incremental encoder for precise position or speed measurement. Parameters at Technoline.cz.

On request
236,41 €
excl. VAT · 286,05 € incl. VAT

Prices include the recycling fee.

Draw-wire incremental encoders

A draw-wire encoder converts a change in distance into unwinding of the wire from a drum; a spring ensures the return. The measured object is connected to the end of the wire and the encoder body to a fixed base. For a correct result, not only the electrical output is essential, but also the position of both fixing points throughout the movement.

Technical document: LARM: draw-wire measurement LS501.

The catalogue name keeps the designation incremental, but the draw-wire mechanism itself does not determine the output principle. The item LS501-10P/1250/R5k L0.25%/KB, LARM, draw-wire encoder, IP65 according to the designation P/R5k and description belongs to the potentiometric version. It cannot automatically be connected as a quadrature A/B encoder.

The output and its evaluation are decisive

With a pulse version, the electronics count increments; conversion to length is based on the travel per drum revolution, the number of periods and the counter mode. With a potentiometer, the wiper position is evaluated. When wired as a voltage divider, verify the permitted excitation, wiper load and input resistance of the measuring device. A bare potentiometer is not automatically a 0–10 V or 4–20 mA transmitter.

If you need pulse measurement, the counter checking procedure can be found in the category Incremental Encoders. The presence of index Z need not mean a single mark in the entire stroke: with the incremental version LS501 described, it repeats as the drum rotates. Homing must therefore also determine the relevant part of the travel.

Measuring geometry and wire guidance

The wire senses the change in its extended length. If the fixing point moves obliquely relative to the encoder, this change may not correspond to the travel of the required axis. First draw the position of the wire at the start, middle and end of the stroke. Check whether the lateral deflection changes, whether the wire rubs anywhere and whether there is a collision with moving parts.

Observe the permitted exit angle according to the specific mechanism. If a change of direction is necessary, design a suitable guide pulley according to the manufacturer's instructions; do not bend the wire over an edge. Verify the measuring range, permissible speed, acceleration and pull force. Do not let a disconnected end rewind abruptly on its own. During mounting, also consider the direction of water ingress into the outlet and protection of the wire against dirt.

Technical document: Micro-Epsilon: wire guidance and mounting principles (PDF).

Model example: lateral offset of the encoder

For our own geometric analysis, consider an ideally tensioned straight wire and a fixed lateral offset h = 100 mm. Its length is L = square root(x² + h²). When the coordinate x moves from 100 to 1 000 mm, the length changes approximately from 141.4 to 1 005.0 mm.

The actual axis travel is 900 mm, but the change in wire length is only 863.6 mm. The difference of 36.4 mm arises from geometry, not from the resolution of the electronics. The model does not assess the permitted exit angle of any product; it shows why the measuring arrangement should be checked before choosing a finer encoder.

Common mistakes and verification after mounting

Is it enough to zero the reading in the lower position?

Zeroing removes the offset of the origin but does not solve the non-linear relationship caused by oblique guidance. Compare the reading with a reference measurement at several points and in both directions of movement.

Can I use a cable with the same connector?

First compare the pin assignment for the specific output. A potentiometer and a pulse encoder can have different contact functions. The principles of checking cabling and mounting are also summarised by Incremental encoder accessories. During acceptance, verify the smoothness of the reading and the return to the same positions throughout the planned stroke.

Cookies on this website

We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.