Phone +420 774 723 123 Cart · 0 · empty

Incremental Encoder Accessories

Accessories for rotary encoders – shaft couplings, mounting brackets and flanges, measuring wheels and cables. Choose by shaft and encoder type.

Filters
Found 5 products

bracket IRC30x/ARC40x, LARM, encoder bracket IRC30x/ARC40x

Cat. no.: držák IRC30x/ARC40x

bracket IRC30x/ARC40x LARM – rotary encoder bracket. Industrial product for automation, measurement and control.

On request
18,05 €
excl. VAT · 21,84 € incl. VAT

bracket IRC31x/ARC41x, LARM, encoder bracket IRC31x/ARC41x

Cat. no.: držák IRC31x/ARC41x

bracket IRC31x/ARC41x LARM – rotary encoder bracket. Industrial product for automation, measurement and control.

On request
18,50 €
excl. VAT · 22,39 € incl. VAT

SP9, LARM, constant-velocity coupling

Cat. no.: SP9

SP9 LARM – constant-velocity coupling for rotary encoder. Industrial product for automation, measurement and control.

On request
24,93 €
excl. VAT · 30,16 € incl. VAT

SV9, LARM, constant-velocity coupling

Cat. no.: SV9

SV9 LARM – constant-velocity coupling for rotary encoder. Industrial product for automation, measurement and control.

On request
35,24 €
excl. VAT · 42,64 € incl. VAT

IRC536/100KA, LARM, incremental handwheel

Cat. no.: IRC536/100KA

IRC536/100KA LARM – incremental handwheel. Industrial product for automation, measurement and control.

On request
228,26 €
excl. VAT · 276,20 € incl. VAT

Prices include the recycling fee.

Incremental encoder accessories

Accessories connect the encoder to the machine mechanically and to the control system electrically. A well-chosen number of pulses will not help if the coupling loads the shaft inappropriately or the cable does not transmit the signal to the receiver. Therefore divide the selection into fixing the body, transmitting rotation and electrical wiring.

The range includes SP9 and SV9 couplings as well as brackets for selected IRC/ARC series. The choice of the encoder itself is addressed by Incremental rotary encoders. Assemble the cable according to the specific wiring; the existence of cables in the manufacturer's programme does not mean confirmed availability of every variant in this category.

A coupling must suit more than just the bore diameter

A coupling transmits rotation and compensates mounting deviations within the permitted range. Distinguish between radial offset of parallel axes, angular misalignment and axial displacement. Verify both clamped shafts, their insertion, speed and torsional stiffness. Do not consider the maximum deviations in different directions as simultaneously usable without the manufacturer's documentation.

LARM SP9, constant-velocity coupling is a disc type; LARM SV9, constant-velocity coupling is a bellows type. The LARM documentation states 9 bores of 6/6 mm for both variants. For the SP series it states a limit of 6 000 rpm and a torsional stiffness of 30 N·m/rad, for SV 10 000 rpm and 200 N·m/rad. The values belong to these series and do not represent universal coupling parameters.

Technical document: LARM: parameters of SP and SV couplings.

Model example: elastic twist

In a simple static model, a torque of 0.03 N·m acts on the coupling. At a stiffness of 30 N·m/rad, the twist is 0.001 rad, i.e. approximately 0.057°. At 200 N·m/rad, it is approximately 0,0086°. The calculation uses the relationship angle = torque / torsional stiffness.

This is a chosen load model, not a measurement of the accuracy of the SP9/SV9. couplings. However, it shows why elasticity should be monitored as well as backlash: the encoder reading behind the coupling may differ under load from the angle on its input side. For rapid changes in movement, the dynamics of the assembly must also be assessed.

A bracket must not forcibly align the assembly

Compare the centring surfaces, hole spacing, threads and mounting space. The bracket should determine the position of the body without deformation; the coupling should not compensate for incorrect alignment of the assembly. Check the fixing before and after tightening. For your own mounting report, record the coupling used, the orientation of the encoder and the method of cable strain relief.

Cables: check pairs, pins and environment

For differential transmission, route the corresponding pairs A+/A−, B+/B− and possibly Z+/Z− in the designated pairs. Compare the pinout of both devices, the connector type and coding, the cross-section of the supply wires and the required length. Handle shield connection, signal reference and termination according to the assembly documentation.

Technical document: EPC: cabling and differential signals (PDF).

For a moving cable, verify suitability for a cable chain, bending radius and sheath resistance to the environment. Do not confuse the flexibility of the cable in your hand with documented service life under repeated bending. In case of interference, check the routing relative to motor cables and the signal state at the receiver. The principles of levels are summarised by the guide Incremental Encoders.

A handwheel is a separate control element

The listing also includes IRC536/100KA. When choosing it, assess the electrical interface and the method of evaluation in the control system; it is not a mechanical coupling or bracket. In the order specification, distinguish the requirement for manual movement input from feedback measurement of machine position.

FAQ

Does a connector adapter also solve a different interface?

A passive adapter changes the contact connections but does not itself convert HTL to TTL or serial position to A/B. The required electrical function must be verified separately.

Can a coupling be chosen just by higher speed?

Also include dimensions, misalignment, stiffness and forces transmitted to the encoder in the comparison. After mounting, verify a known movement and return in both directions; start-up without a visible collision alone is not a complete check of the measurement.

Cookies on this website

We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.