Phone +420 774 723 123 Cart · 0 · empty

Absolute Encoders

Absolute rotary encoders for measuring angle and position that retain the position even after a power failure – singleturn and multiturn. Choose by resolution, interface (SSI, analogue, fieldbus) and shaft.

Filters
Found 1 products

ARC410/10KA, LARM, absolute rotary encoder

Cat. no.: ARC410/10KA

ARC410/10KA LARM – absolute rotary encoder. Industrial product for automation, measurement and control.

On request
296,37 €
excl. VAT · 358,61 € incl. VAT

Prices include the recycling fee.

Absolute encoders

The name of this catalogue category combines terms that technically denote different principles. An incremental encoder transmits increments of movement, an absolute encoder provides a position code within its measuring range. Some absolute devices also have an incremental track, but the combined category name does not confirm such equipment for all products.

Start the selection with the question of what position the control system must know after switching on: the angle within one revolution, or also the number of complete revolutions of the mechanism? The decision relates to the transmission ratio and working range of the machine. An overview of the differences is contained in the parent category Incremental Encoders.

Singleturn and multiturn address a different range

Singleturn distinguishes angular positions within one revolution. After turning through a full 360°, the same position code repeats. Multiturn adds information about the number of revolutions within a defined range. More bits for the angle therefore do not replace multi-turn information. For multiturn versions, also check the behaviour during movement without power: the method of counting revolutions depends on the design, for example mechanics, a battery or energy harvesting from motion.

Technical document: Kübler: singleturn; Kübler: separation of singleturn and multiturn (PDF).

The absolute value of the encoder need not yet correspond to the working zero of the machine. During commissioning, assign the machine coordinate to the measured code and verify the direction and the transition across the end of the range. Use the preset function or setting input only if the specific type actually supports it.

Choose the interface according to the control unit

  • A parallel output transmits individual bits via separate wires. Check their number, electrical levels, method of simultaneous reading and coding.
  • SSI transmits position serially according to the clock signal from the evaluation unit. The data word length, clock frequency and binary or Gray coding must match.
  • BiSS and industrial fieldbuses require a corresponding interface and a supported protocol in the control system. An identical connector alone does not ensure communication.

This is an overview of possible absolute sensing solutions, not a statement that every product in this category offers all variants. RS422 describes electrical transmission; the value RS422 alone does not distinguish incremental A/B from a serial position interface. For connection, you need the complete specification of both ends.

Technical document: EPC: SSI transmission parameters (PDF).

Model example: screw with a lead of 5 mm per revolution

Consider a directly connected encoder with 12-bit singleturn resolution and an ideal screw without backlash. One revolution has 4 096 positions; the calculated feed step is 5/4 096 = approximately 0,00122 mm. This step does not indicate the accuracy of the screw or the assembly.

With a stroke of 300 mm, the screw rotates 60 times. The singleturn code alone repeats within this stroke, so after switching on it does not unambiguously determine the carriage position. For your own design, verify the multiturn range, its retention during a power failure and the reserve relative to the end stops. The numbers in the example are chosen for the calculation and do not describe a specific catalogue item.

Mechanical connection and test after replacement

Compare the shaft, centring, flange, bearing load and space for the connector. Look for suitable mounting in the category Incremental encoder accessories. During acceptance, check several known positions, a change of direction and restart. Also note the working zero offset in the report so that the next replacement does not depend on the operator's memory.

FAQ

Can an absolute encoder be wired in place of A/B/Z?

Only if it has the required compatible output or suitable evaluation is part of the design. For conventional quadrature counters, also compare Incremental rotary encoders.

Is zero setting always unnecessary?

No. Recognising the encoder's own position and assigning the machine coordinate are two separate tasks. After a mechanical shift of the coupling or replacement of the encoder, verify the relation of the position to the mechanism again.

Cookies on this website

We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.