Sonoff DIY BasicR3, Sonoff, smart WiFi switch, 100-240 VAC, 10 A
Sonoff DIY BasicR3 by Sonoff – smart 10 A Wi-Fi switch, 100-240 V AC. Technical specifications, applications, installation and selecting the correct variant.
Rate 24,43 CZK per 1 EUR. Prices are indicative, invoicing is in Czech crowns.
Sonoff Basic R3 and RF R3 WiFi switches for remotely switching appliances via an app or remote control. Choose by control, load and supply.
Sonoff DIY BasicR3 by Sonoff – smart 10 A Wi-Fi switch, 100-240 V AC. Technical specifications, applications, installation and selecting the correct variant.
Sonoff DIY RFR3 by Sonoff – smart 10 A Wi-Fi + RF switch, 100-240 V AC. Technical specifications, applications, installation and selecting the correct variant.
Prices include the recycling fee.
A WiFi switch sends a command to turn an electrical load on or off over a data network. When selecting a device, assess the power circuit, availability of the communication path and behaviour after a restart separately. Use the device for operational or convenience control, such as standard lighting; do not incorporate these switches into machine safety functions.
The range includes Sonoff DIY BasicR3 and Sonoff DIY RFR3, both rated at 100–240 V AC and 10 A. The RFR3 also supports control in the 433.92 MHz band. The eWeLink app is used for standard phone control; assess the available features according to the selected mode and current version.
Shared SONOFF BASICR3/RFR3 manual confirms 2.4 GHz WiFi, a local button and separate RF control on the RFR3. The BASICR3 does not support this RF controller.
The manual connects the mains supply to L In/N In and the load to L Out/N Out. In your design, therefore, treat these devices as mains-load switches, not as universal potential-free outputs for arbitrary control circuits.
Choose the variant according to the required method of operation. The radio controller and phone provide different control paths to the same switched circuit. Establish who may operate the device and how they will determine its current status. A successfully sent command or an old value in the app does not prove that the connected appliance is actually operating.
Before installation, assess coverage at the final installation location, with the enclosure closed and nearby equipment operating normally. A phone beside an open control cabinet may not experience the same conditions as the installed switch. Also distinguish loss of internet access from loss of connection to the local access point.
Do not automatically apply the current rating to every type of load. LED power supplies, motors and transformers may draw a substantially different current at start-up than during steady operation. Verify the permitted load type, inrush characteristics, switching frequency and installation conditions. Switching off through the app does not isolate the circuit for safe work on the wiring.
SONOFF DIY mode documentation for the BASICR3 and RFR3 describes local control without the cloud; DIY 2.0 is associated with firmware 3.5.0. The local network must still be operational.
When the internet is unavailable, the outcome therefore depends on whether you use local control or a service that requires a remote server. Switching off the access point also interrupts the network path for local control. Do not treat an ‘offline’ status as confirmation that the output is off. Monitor the operating state of the load separately and provide suitable local access for the required control method.
For the RFR3, the manual describes a paired RF controller as local wireless control independent of WiFi. This still requires the switch to be powered and within a working radio range.
SONOFF DIY protocol for BASICR3/RFR3 distinguishes the power-on state settings: on means switch on, off means switch off, and stay restores the previous state. Configure and verify this behaviour in a supported mode and firmware version.
Select the response according to the appliance and the consequences of operation resuming automatically. Power may return to the switch before the router is ready. During commissioning, therefore, observe the state immediately after power-up and again after communication is established. Treat an automatic schedule, a manual command and the power-on state setting as separate events.
For a sample lighting circuit, test two initial states, on and off, against three situations: loss of internet access, switching off the access point and interrupting power to the switch. This produces 2 × 3 = 6 basic scenarios. Define the required behaviour for each scenario in advance and record the actual load state, control availability and response after recovery. This is a user-defined test model, not a guarantee of device behaviour.
For each scenario, add a check of local control and repeat the command after the connection is restored. Perform the test with a suitable, harmless load and with access to isolation available. Record the result together with the firmware version and selected mode; retest the affected behaviour after changing settings or updating the device.
No. When designing a control station, you can use Push-button boxes, but safety functions require their own appropriate solution. WiFi, the cloud and convenience RF controllers are not machine safety channels.
Frequency alone does not confirm compatibility. The encoding and supported pairing method must also match; select the controller according to its specific documentation.
No. Installation and servicing must be carried out by a qualified person with the circuit isolated and absence of voltage verified. A network command does not replace electrical isolation of the circuit.
We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.
Choose which cookies we may use. You can change your choice at any time.
They keep the cart contents, your login and selected language, and protect forms from abuse. An order cannot be completed without them, so they are used even without consent.
Google Analytics shows us traffic and behaviour on the website in aggregated form. This tells us which pages are not working for people. We do not identify anyone from this data.