Phone +420 774 723 123 Cart · 0 · empty

MK1 Plastic Limit Switches

EMAS MK1 plastic miniature limit switches with lever or roller. Choose by actuating element.

Filters
Found 12 products
OUR TIP IN STOCK

MK1MIP2, EMAS, microswitch, MK1, roller lever, 1 CO

Cat. no.: MK1MIP2

MK1MIP2 EMAS – microswitch, MK1, roller lever, 1 CO. Technical parameters, application and compatibility check.

In stock 5 or more pcs
4,63 €
excl. VAT · 5,60 € incl. VAT
OUR TIP IN STOCK

MK1PUP1, EMAS, microswitch, MK1, plunger, 1 CO

Cat. no.: MK1PUP1

MK1PUP1 EMAS – microswitch, MK1, plunger, 1 CO. Technical parameters, application and compatibility check.

In stock 5 or more pcs
4,63 €
excl. VAT · 5,60 € incl. VAT
OUR TIP IN STOCK

MK1KIM1, EMAS, microswitch, MK1, lever, 1 CO

Cat. no.: MK1KIM1

MK1KIM1 EMAS – microswitch, MK1, lever, 1 CO. Technical parameters, application and compatibility check.

In stock 5 or more pcs
5,08 €
excl. VAT · 6,14 € incl. VAT
OUR TIP IN STOCK

MK1KIM2, EMAS, microswitch, MK1, lever, 1 CO

Cat. no.: MK1KIM2

MK1KIM2 EMAS – microswitch, MK1, lever, 1 CO. Technical parameters, application and compatibility check.

In stock 5 or more pcs
5,08 €
excl. VAT · 6,14 € incl. VAT
OUR TIP IN STOCK

MK1KIM3, EMAS, microswitch, MK1, lever, 1 CO

Cat. no.: MK1KIM3

MK1KIM3 EMAS – microswitch, MK1, lever, 1 CO. Technical parameters, application and compatibility check.

In stock 5 or more pcs
5,08 €
excl. VAT · 6,14 € incl. VAT
OUR TIP IN STOCK

MK1KIM4, EMAS, microswitch, MK1, lever, 1 CO

Cat. no.: MK1KIM4

MK1KIM4 EMAS – microswitch, MK1, lever, 1 CO. Technical parameters, application and compatibility check.

In stock 5 or more pcs
5,08 €
excl. VAT · 6,14 € incl. VAT
OUR TIP IN STOCK

MK1KIM5, EMAS, microswitch, MK1, lever, 1 CO

Cat. no.: MK1KIM5

MK1KIM5 EMAS – microswitch, MK1, lever, 1 CO. Technical parameters, application and compatibility check.

In stock 5 or more pcs
5,08 €
excl. VAT · 6,14 € incl. VAT
OUR TIP IN STOCK

MK1MIM1, EMAS, microswitch, MK1, roller lever, 1 CO

Cat. no.: MK1MIM1

MK1MIM1 EMAS – microswitch, MK1, roller lever, 1 CO. Technical parameters, application and compatibility check.

In stock 5 or more pcs
5,08 €
excl. VAT · 6,14 € incl. VAT
OUR TIP IN STOCK

MK1MIM2, EMAS, microswitch, MK1, roller lever, 1 CO

Cat. no.: MK1MIM2

MK1MIM2 EMAS – microswitch, MK1, roller lever, 1 CO. Technical parameters, application and compatibility check.

In stock 5 or more pcs
5,08 €
excl. VAT · 6,14 € incl. VAT
OUR TIP IN STOCK

MK1MIP1, EMAS, microswitch, MK1, roller lever, 1 CO

Cat. no.: MK1MIP1

MK1MIP1 EMAS – microswitch, MK1, roller lever, 1 CO. Technical parameters, application and compatibility check.

In stock 5 or more pcs
5,08 €
excl. VAT · 6,14 € incl. VAT
OUR TIP IN STOCK

MK1MIP3, EMAS, microswitch, MK1, roller lever, 1 CO

Cat. no.: MK1MIP3

MK1MIP3 EMAS – microswitch, MK1, roller lever, 1 CO. Technical parameters, application and compatibility check.

In stock 5 or more pcs
5,08 €
excl. VAT · 6,14 € incl. VAT
OUR TIP IN STOCK

MK1PUP1Y, EMAS, microswitch, MK1, plunger, 1 CO

Cat. no.: MK1PUP1Y

MK1PUP1Y EMAS – microswitch, MK1, plunger, 1 CO. Technical parameters, application and compatibility check.

In stock 5 or more pcs
5,08 €
excl. VAT · 6,14 € incl. VAT

Prices include the recycling fee.

Plastic Limit Switches MK1

MK1 switches make it possible to solve mechanical detection in small assemblies. The design must leave space not only for the body, but also for the lever movement and the connection terminals. For sensing for a control input, add a timing question: when does the contact change actually take effect in the program? The mechanical position and the processed information are not the same data.

Choose the actuator and connection together

The public range includes MK1MIP2. Its EMAS sheet states a long lever with a plastic roller, one changeover contact and connection tabs 6.3 × 0.8 mm. These dimensions describe the connection, not the whole switch.

Before mounting, compare the connector receptacle used with the tab size and the conductor. Add space for plugging in, disconnecting and strain relief of the wiring to the sketch. Sometimes the body fits the available space, but once the terminated wires are added the assembly can no longer be safely assembled or removed. This problem is easier to solve on the drawing than during a shutdown.

Low current requires its own assessment

For a control input, also check the minimum contact load conditions. The OMRON diagnostic overview states that contact problems may also be related to a very small switched load. A high maximum current therefore does not automatically confirm suitability for a weak signal.

Prepare data on the actual input: voltage, current, evaluation method and any filtering. If the catalogue does not provide any of the required properties, list it as an open point of the selection. Merely replacing the contact with a new one may not remove a fault whose cause lies in an unsuitable combination of input and switch.

Author's example: delay and position

Consider a model moving part with a speed of 250 mm/s. Processing the input change in the practice control adds a delay of 4 ms. During this time, the movement travels 250 × 0.004 = 1.0 mm. With a model delay of 12 ms, it is already 3.0 mm.

The figures are not the response time of MK1MIP2 nor the setting of a specific PLC. The example merely converts a time difference into a position. It does not include braking, variable speed or further delays. It cannot be used as a calculation of a safe distance or of the exact stopping point of the machine.

The practical conclusion is to also record the input setting during the test. Otherwise, after a program change, the position of the processed event may shift even though the lever and cam have remained in the same place. The mechanical and electrical parts of the diagnostics can thus be compared separately.

Mounting check and FAQ

The fastening and wire routing must allow the correct working movement. OMRON mounting guidelines for basic switches point out protection against lead pull and dirt. However, the dimensions, forces and permissible travel are determined by the documentation of the specific MK1.

At handover, note the cam contact point, the maximum lever deflection and the return. A common mistake is to test only the electrical switching and overlook that the moving part continues further and loads the actuator outside the designed path.

Is 1CO a pair of independent contacts?

No. It is one changeover contact; assess the wiring according to its diagram and terminal markings.

Can MK1 be interchanged with MN1 just by the contact?

Also compare the connection, fastening and actuator. Helpful categories are Plastic Limit Switches MN1 and the common overview Miniature Limit Switches.

Cookies on this website

We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.