Phone +420 774 723 123 Cart · 0 · empty

Individual modules and accessories

Individual modules and accessories for EMAS 70 mm IP65 beacons for assembling or repairing the beacon.

Filters
Found 5 products

IKM7KE, EMAS, signal module 70 mm, red, 24V DC, 70 mm, IP65

Cat. no.: IKM7KE

IKM7KE EMAS - signal module 70 mm, red, 24V DC, 70 mm, IP65. Technical specifications, use, installation and selection of the correct variant.

On request
17,93 €
excl. VAT · 21,70 € incl. VAT

IKM7YE, EMAS, signal module 70 mm, green, 24V DC, 70 mm, IP65

Cat. no.: IKM7YE

IKM7YE EMAS - signal module 70 mm, green, 24V DC, 70 mm, IP65. Technical specifications, use, installation and selection of the correct variant.

On request
17,93 €
excl. VAT · 21,70 € incl. VAT

IKM7RE, EMAS, signal module 70 mm, yellow, 24V DC, 70 mm, IP65

Cat. no.: IKM7RE

IKM7RE EMAS - signal module 70 mm, yellow, 24V DC, 70 mm, IP65. Technical specifications, use, installation and selection of the correct variant.

On request
17,93 €
excl. VAT · 21,70 € incl. VAT

IKM7BE, EMAS, signal module 70 mm, white, 24V DC, 70 mm, IP65

Cat. no.: IKM7BE

IKM7BE EMAS - signal module 70 mm, white, 24V DC, 70 mm, IP65. Technical specifications, use, installation and selection of the correct variant.

On request
17,93 €
excl. VAT · 21,70 € incl. VAT

IKM7ME, EMAS, signal module 70 mm, blue, 24V DC, 70 mm, IP65

Cat. no.: IKM7ME

IKM7ME EMAS - signal module 70 mm, blue, 24V DC, 70 mm, IP65. Technical specifications, use, installation and selection of the correct variant.

On request
17,93 €
excl. VAT · 21,70 € incl. VAT

Prices include the recycling fee.

Individual modules and accessories

When assembling or repairing an EMAS 70 mm lamp in the IP65 branch, select each part according to its full marking. In the catalog, there are color modules IKM7KE, IKM7YE, IKM7RE, IKM7BE, and IKM7ME without LED bulbs and an adapter with a plug IKM7G. The default overview provides an overview of the category Economic beacons - diameter 70mm EMAS (IP65)For service replacement document the current configuration first.

What to see in the component roster

Assign a color module and corresponding light source to each lighting panel. Record the base, end, and method of cable routing in the same layout. Select the source between LED bulbs up to 50mm and 70mm beacons Emas according to voltage, colour and required light. Check the actual content of the item so that the electrical or mechanical part is not missing during assembly.

For an already installed pole, compare the designation on the part with the machine documentation. If it differs, document the difference before purchasing a replacement. A simple photograph or diameter is not enough; the joint construction and part execution are also important. When expanding to another color, check the space above the pole and the necessary independent control signal.

Installation with respect to the resulting coverage

Before disassembly, disconnect the power and prepare a clean work area. Check the mating surfaces, end, and cable routing. Do not repair a damaged joint with increased force during assembly. After installation, do not mechanically load the connection point, and the assembly must be firmly secured. The service record should be supplemented with the actual designation of the replacement components.

For the individual part and finished column, the same cover conclusion cannot be used automatically. Require a base for the selected combination including assembly. EMAS (page 76)Expansion of acoustics therefore requires verification of the entire proposal. For comparison with defined configuration use Compound beacons.

Model example of repair

During maintenance, if a burnt-out color part is found while the light source is functioning, the technician should note the original code and verify the corresponding replacement. Before swapping, check adjacent joints, as visible damage may not be the only result of mechanical strain. After assembly, perform a functional test and cable routing check. The new module itself is not proof of the restored cover of the entire installation.

Frequently Asked Questions

Can I take the base from the older beacon?

Only after verification that it corresponds to the selected configuration and is undamaged. The inclusion of the part in the related category does not replace this check.

Does the color of the module determine its power supply?

Verify the power supply at the input lamp and other electrical components.

Is the resulting column a safety device?

No. It is designed to signal operating conditions. Its colour, installation or marking of the cover cannot be derived from the ability to ensure the protective function of the machine.

Cookies on this website

We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.