Phone +420 774 723 123 Cart · 0 · empty

Torque Sensors

SMOWO torque sensors for measuring torque on a shaft. Choose by range, design and output.

Filters
Found 5 products
−3 % OUR TIP IN STOCK

LCS-T1-2Nm, SMOWO, torque sensor, 2 Nm, PVC cable 2m with 4 PIN connector

Cat. no.: LCS-T1-2Nm

LCS-T1-2Nm SMOWO – torque sensor, 2 Nm, PVC cable 2m with 4 PIN connector. Industrial product for automation, measurement and control.

In stock 1 ks
325,21 € 335,27 €
excl. VAT · 393,51 € incl. VAT
OUR TIP IN STOCK

LCS-T1-5Nm, SMOWO, torque sensor, 5 Nm, PVC cable 2m with 4 PIN connector

Cat. no.: LCS-T1-5Nm

LCS-T1-5Nm SMOWO – torque sensor, 5 Nm, PVC cable 2m with 4 PIN connector. Industrial product for automation, measurement and control.

In stock 4 ks
335,27 €
excl. VAT · 405,67 € incl. VAT
IN STOCK

LCS-T1-1Nm, SMOWO, torque sensor, 1 Nm, PVC cable 2m with 4 PIN connector

Cat. no.: LCS-T1-1Nm

LCS-T1-1Nm SMOWO – torque sensor, 1 Nm, PVC cable 2m with 4 PIN connector. Industrial product for automation, measurement and control.

In stock 2 ks
335,27 €
excl. VAT · 405,67 € incl. VAT
IN STOCK

LCS-T1-10Nm, SMOWO, torque sensor, 10 Nm, PVC cable 2m with 4 PIN connector

Cat. no.: LCS-T1-10Nm

LCS-T1-10Nm SMOWO – torque sensor, 10 Nm, PVC cable 2m with 4 PIN connector. Industrial product for automation, measurement and control.

In stock 2 ks
355,73 €
excl. VAT · 430,44 € incl. VAT
OUR TIP IN STOCK

LCS-T1-20Nm, SMOWO, torque sensor, 20 Nm

Cat. no.: LCS-T1-20Nm

LCS-T1-20Nm SMOWO – torque sensor, 20 Nm. Industrial product for automation, measurement and control.

In stock 2 ks
387,25 €
excl. VAT · 468,58 € incl. VAT

Prices include the recycling fee.

Torque sensors

Choose a torque sensor according to the working range, mounting method and movement of the measured part. This category is represented by the SMOWO LCS-T1. series. For checking a tightening fixture or reaction torque, it is essential to know whether it is a steady load, a short event or a continuously rotating shaft. These tasks are not interchangeable.

LCS-T1 and limits of use

The manufacturer specifies LCS-T1 for static tests and non-continuous rotation. It states an output sensitivity of 1.0–1.5 mV/V and excitation of 5–12 V with 10 V recommended; verify the specific conversion for the selected variant. Suitability for continuous shaft rotation cannot be derived from this specification. The basis is SMOWO documentation LCS-T1. When designing the fixture, also check the cable routing throughout the permitted movement.

N·m is not a force in newtons

Torque depends on both force and lever arm: with perpendicular action, M = F × r. With an oblique direction, the perpendicular distance of the axis from the line of action of the force is decisive. The same force gauge with levers of different lengths therefore represents a different torque. For separate measurement of tensile or compressive force, use Strain gauge sensors; merely changing the units of their output does not create torque measurement.

Distinguish between a reaction arrangement and measurement on a rotating element. At the same time, assess radial and axial forces as well as bending, which the fixture or a misaligned coupling can add to the measuring point. These relationships are summarised by the NI torque measurement guide. Nominal torque does not automatically mean that any combination of side loads is permissible.

Mounting and electrical compatibility

Before manufacturing adapters, check the dimensional drawing, connection interface and torque transmission path. The fixture should load the specified axis; it must not force the position of the sensor by elastic bending of the brackets. In the work procedure, define the positive direction and keep it for wiring, evaluation and reference testing.

For a small output in mV/V, you need a suitable measuring input. When choosing from strain gauge amplifiers compare the supported sensitivity, excitation voltage, zero offset and any negative signal. The transmitter supply is not automatically the sensor excitation. For a bidirectional test, it is not enough to set the device only for the positive part of the range; both directions must also be accepted by the subsequent analogue input or data processing.

Model example of a test lever

A known force of 20 N acts perpendicularly on a horizontal arm 0.15 m long. The ideal torque is 3 N·m. Moving the same force to a distance of 0.30 m creates 6 N·m, not a greater force. For a measuring range of 5 N·m, the second arrangement would already exceed the nominal value. This own calculation assumes a rigid lever, a precisely defined axis and a perpendicular direction; it does not include friction, the weight of the fixture or start-up shock. It does not replace calibration of the finished equipment.

Calibration and capturing a short event

For calibration, determine the required range, direction and loading mode. The method must correspond to the use; a static reference alone does not verify the dynamic response. The choice of calibration and test methods is addressed by the NPL metrology guide for torque transducers. Zeroing without load does not replace checking the conversion at a known torque.

When evaluating a peak, check the entire time response. Averaging can reduce the measured maximum even though the steady value remains correct. Record the filter setting, the rate of genuinely new samples and the length of the event examined; communication frequency is not the same as measuring bandwidth.

FAQ

Can I measure negative torque simply by inverting the sign?

Not without verification. Both the mechanical specification of the sensor and the electrical range of the entire assembly must be suitable. The sign in the program only describes the agreed orientation.

Is it always enough to set zero before each test?

Zero helps separate the initial state but can hide a preload of the fixture. First check the mechanical unloading and only then store the zero reference.

Cookies on this website

We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.