H100DM, EMAS, Blue illuminated push button, 30 mm, 1 normally open contact, without LED
H100DM EMAS – control push button 30 mm, blue, 1 NO, 500 V DC, IP50. Technical parameters, application, mounting and selection of the right variant.
Rate 24,43 CZK per 1 EUR. Prices are indicative, invoicing is in Czech crowns.
EMAS H series push buttons for 30 mm mounting, including illuminated versions. Choose by colour, contacts and illumination.
H100DM EMAS – control push button 30 mm, blue, 1 NO, 500 V DC, IP50. Technical parameters, application, mounting and selection of the right variant.
H100DS EMAS – control push button 30 mm, yellow, 1 NO, 500 V DC, IP50. Technical parameters, application, mounting and selection of the right variant.
H100DB EMAS – control push button 30 mm, white, 1 NO, 500 V DC, 30 mm. Technical parameters, application, mounting and selection of the right variant.
H100DK EMAS – control push button 30 mm, red, 1 NO, 500 V DC, IP50. Technical parameters, application, mounting and selection of the right variant.
H100DY EMAS – control push button 30 mm, green, 1 NO, 500 V DC, IP50. Technical parameters, application, mounting and selection of the right variant.
H100DH EMAS – control push button 30 mm, red, 1 NO, 500 V DC, IP50. Technical parameters, application, mounting and selection of the right variant.
Prices include the recycling fee.
This group is intended for panel designs with a mounting size of 30 mm. The range includes EMAS push buttons H100DY, H100DK, H100DM, H100DS and H100DB, which are listed without an LED and with one normally open contact. For the resulting light function, selecting the actuator colour is therefore not enough. A complete solution must be assembled, including a suitable light module and its supply.
For example, the manufacturer describes H100DY as a green flat momentary push button of size 30 mm with a 1NO. contact For the contact, it states 4 A at 250 V AC and category AC-15. See the EMAS H100DY technical sheet. This value belongs to the contact; it is not the voltage of the missing LED or a promise of switching any power load.
Divide the order into the functional unit of the actuator and the illumination requirement. For an added module, the designation for the given series, mechanical attachment, light path through the actuator and electrical parameters must match. A higher current rating cannot be derived from a larger front dimension. Likewise, a module from a smaller actuator cannot be used without confirmation of compatibility.
The size 30 mm is not a complete specification for making the hole. The drawing of the specific assembly is decisive, including tolerances, material thickness, any position locking and the seating surface. In front of the panel, take into account the frame and label; behind the panel, the contacts, light part, terminals and wire bends. Rear components must not collide with the mounting plate, even when closing the door.
When switching from Illuminated push buttons, mounting 22 mm it is a change of the mechanical design, not a simple electrical replacement. Any reducing or cover element must be intended for the given assembly. An overview of other versions can be found in the category Push Button Switches.
Consider a proposed actuator whose complete rear assembly, according to the design assumption, has a depth of 55 mm from the inner surface of the door. The designer also reserves 25 mm for wire routing. The required space is therefore 55 + 25 = 80 mm. If there is only 72 mm to the nearest obstacle, 8 mm is missing; a free hole in the front panel does not solve this problem.
All numbers in the example are the author's, not the dimensions H100DY. The actual design uses the drawing of the complete assembly and the permitted bends of the specific wires. Adding illumination may change the layout and service access, so the space check is only done on the final list of components.
Define an unambiguous meaning for the light, for example availability of the selected mode. A lit actuator does not automatically mean a closed contact or confirmed movement of the equipment. After mounting, verify the momentary function, the separate light function and legibility under normal ambient lighting. Assess the sealing and protection parameters for the specific installation, not for the whole panel based on a single part.
No. A mechanical contact assembly does not replace a light source. Illumination requires an appropriate fitted light part.
No. Colour is just one property. Mechanical and electrical compatibility confirmed by the manufacturer is decisive; the exact module designation belongs in the bill of materials, not just “green LED”.
If you cannot find the item you need in the e-shop, contact us with your enquiry and the complete specification of the required version.
We need technical cookies for the cart and checkout to work — these are always used. Analytics cookies show us which pages people look for and where they get lost, and help us improve the shop. We only use them if you allow it. More in the data processing policy.
Choose which cookies we may use. You can change your choice at any time.
They keep the cart contents, your login and selected language, and protect forms from abuse. An order cannot be completed without them, so they are used even without consent.
Google Analytics shows us traffic and behaviour on the website in aggregated form. This tells us which pages are not working for people. We do not identify anyone from this data.