Sockets

Sockets for industrial relays for DIN rail or panel mounting. Choose by relay type, number of pins and terminal type.

Filtry
Znaleziono 8 produktów
DOSTĘPNY

DYF14A, QIANJI, socket for 14-pin relays with 4 changeover contacts

Nr kat.: DYF14A

The QIANJI plug-in socket DYF14A is intended for 14-pin industrial relays with four changeover contacts. It allows the relay to be connected in a control cabinet and makes its possible replacement…

Dostępny 5 i więcej szt.
1,60 €
bez VAT · 1,94 € z VAT
DOSTĘPNY

GZT4B, RELPOL, socket for 14-pin relay R4N with 4 changeover contacts

Nr kat.: GZT4B

RELPOL socket GZT4B for connecting a R4N series plug-in relay in a control cabinet. It is intended for the fourteen-pin relay version with four changeover contacts.

Dostępny 5 i więcej szt.
1,89 €
bez VAT · 2,29 € z VAT
NASZA PORADA DOSTĘPNY

RS2.M2CO.08V.S0, EMAS, DIN-rail relay socket for PCB relays RE2, 4/5/6/8 pins, 250VAC

Nr kat.: RS2.M2CO.08V.S0

RS2.M2CO.08V.S0, EMAS, DIN-rail relay socket for PCB relays RE2, 4/5/6/8 pins, 250VAC. Socket RS2.M2CO.08V.S0 is designed for DIN-rail mounting and for inserting suitable power relays RE2 with…

Dostępny 5 i więcej szt.
2,83 €
bez VAT · 3,43 € z VAT
DOSTĘPNY

GZM80, RELPOL, plug-in socket for miniature relays, 2 changeover contacts, DIN

Nr kat.: GZM80

GZM80, RELPOL, plug-in socket for miniature relays, 2 changeover contacts, DIN. Relpol GZM80 is a compact screw socket for selected series of miniature relays RM84, RM85 and RM87L/RM87P.

Dostępny 5 i więcej szt.
2,87 €
bez VAT · 3,48 € z VAT
DOSTĘPNY

GZT92, RELPOL, screw socket for relay RM87N, 1-pole, DIN 35mm

Nr kat.: GZT92

GZT92, RELPOL: screw socket for DIN 35mm for relays RM87N and RM87N Sensitive, rated load 12A/300VAC.

Dostępny 5 i więcej szt.
2,87 €
bez VAT · 3,48 € z VAT
−3 % DOSTĘPNY

GZT4, RELPOL, plug-in socket for relay R4N, 4 changeover contacts, DIN

Nr kat.: GZT4

GZT4, RELPOL, plug-in socket for relay R4N, 4 changeover contacts, DIN. Socket GZT4 is used for connecting four-pole industrial relays R4N and allows the relay to be replaced without disconnecting…

Dostępny 5 i więcej szt.
3,07 € 3,16 €
bez VAT · 3,71 € z VAT
DOSTĘPNY

RS1P11G1, EMAS, socket for 11-pin relay

Nr kat.: RS1P11G1

RS1P11G1 EMAS – socket for 11-pin relay. Exact technical data for selecting the relay socket type.

Dostępny 5 i więcej szt.
4,92 €
bez VAT · 5,96 € z VAT
−3 % DOSTĘPNY

PI6W-1P, RELPOL, screw socket for relay RM699BV, 1CO, width 6.2mm, DIN 35mm

Nr kat.: PI6W-1P

PI6W-1P, RELPOL: feed-through socket with screw terminals for RM699BV and RSR30, width 6.2mm, DIN rail 35mm.

Dostępny 5 i więcej szt.
9,15 € 9,43 €
bez VAT · 11,07 € z VAT

Ceny zawierają opłatę recyklingową.

Sockets

A socket connects a plug-in relay to the wiring and determines the method of its mechanical fixing. When selecting, start with the exact designation of the relay for which you are looking for a base. The number of pins is only one piece of identification data. Alongside it, compare the layout of the terminals, their function, the terminal design and the accessories that are to remain part of the assembly.

Deciding according to the specific relay

This category includes, for example, GZM80, GZT4, GZT92, RS1P11G1 and PI6W-1P. The range also includes EMAS RS2.M2CO.08V.S0 and DYF14A. These codes do not represent one interchangeable series. Look for the switching part itself in the category Relay; when ordering the base, attach its complete designation including the variant.

RELPOL drawing for GZM80 specifies compatible families, terminals and accessories. External similarity therefore does not replace a comparison of the diagram or confirmation of a suitable clip.

When replacing an existing socket, create a terminal conversion list: function in the diagram, designation on the original base and designation on the new one. Do not confuse the view of the relay pins with the view of the base being wired. For each drawing, first find out from which side it is shown.

Principle of the load on the whole assembly

In the current assessment, record the relay, base, jumper element and connected circuit separately. A document for one component does not close the other rows. Request data for the same operating conditions; otherwise the lowest number in the table cannot be presented as the resulting load capacity of the whole assembly. Record the load type and temperature separately.

Author's model example: comparing limits

For a simplified exercise, assume three series-connected parts with limits of 8 A, 6 A and 5 A, all valid for the same model conditions. The preliminary common ceiling will not exceed 5 A. A higher figure on the first part does not transfer its reserve to the other components.

The figures are the author's, not parameters of the products offered. Even the calculated ceiling does not confirm the suitability of a specific load, protection or mounting. The example serves only to expose the error of labelling an assembly with the current of its strongest part. The actual assessment must include all conditions of the relevant manufacturer data.

Mounting the terminals and access to the relay

In the mounting documentation, state the type of conductor, its termination and the number of conductors in one terminal. Check the corresponding manufacturer data for the specific version. Do not take over the stripping length or tightening torque from another base. When laying out, maintain access to the terminals, labels and the space needed to remove the relay.

If the assembly requires a clip or a plug-in protective module, add their codes to the bill of materials. Verify suitable add-ons in relay accessories. The replacement part should also be identifiable when the wiring is complete; a photo of an empty socket does not replace the marking of the actually fitted assembly.

Diagnosing an intermittent connection

Record whether the fault changes after warming up, with vibration or after a service intervention. Divide the inspection record into the relay, insertion into the socket and the connected conductors. A specialist can then evaluate the specific fault location without randomly swapping components. Carry out handling and verification according to the procedure for safely secured equipment.

FAQ

Does the same number of pins mean interchangeability?

No. The function and geometry of the terminals must match, as well as the explicit compatibility of the relay and socket.

Can a missing clip be replaced by any clip?

Verify compatibility for the specific base and relay. External similarity does not prove correct retention of the whole assembly.

Pliki cookies na tej stronie

Techniczne pliki cookies są potrzebne do działania koszyka i zamówienia — są używane zawsze. Analityczne pliki cookies pokazują nam, których stron ludzie szukają i gdzie się gubią, i pomagają nam ulepszać sklep. Użyjemy ich tylko wtedy, gdy na to pozwolisz. Więcej w zasadach przetwarzania danych.