Inductive sensor, NCB3-14GM65-E3-D-V1, 231587, PEPPERL+FUCHS
Inductive sensor, NCB3-14GM65-E3-D-V1, 231587, PEPPERL+FUCHS
Kurs 24,39 Kč za 1 EUR. Ceny są orientacyjne, rozliczenie następuje w koronach czeskich.
High-pressure inductive sensors withstand hydraulic oil pressure and are used to monitor the piston end position directly in the hydraulic cylinder. Choose by permissible pressure, thread, seal and medium.
Inductive sensor, NCB3-14GM65-E3-D-V1, 231587, PEPPERL+FUCHS
Pressure-resistant inductive sensor M12x1, length 138mm, 500bar, DC,pnp,no,Sn:1.5 b,M12 connector
Ceny zawierają opłatę recyklingową.
A high-pressure inductive sensor detects a metal part in a pressurised space, for example the position of a piston or a component of a hydraulic mechanism. Its design must withstand the pressure load and form the specified tight connection. It is a proximity sensor; it does not measure the pressure value.
Start with the pressure directly at the mounting location. In hydraulics, also monitor peaks when valves switch, the number of cycles and the oil temperature. A short surge can exceed the normal working pressure. A test or burst pressure stated in the documentation is not automatically a permissible value for continuous operation.
| Requirement | Basis for selection |
|---|---|
| Pressure load | Continuous pressure, possible peaks and the nature of repeated stress. |
| Process connection | Exact drawing, thread, seating surface, seal and specified tightening. |
| Medium | Name of the fluid, additives, concentration and temperature; compatibility of all wetted parts. |
| Position detection | Target material, minimum and maximum gap, position in the cylinder and speed of movement. |
| Electrical connection | Supply, PNP/NPN, NO/NC and cable resistance along its route. |
IP67 or IP68 describes protection against ingress under defined test conditions. Suitability as part of a hydraulic pressure chamber cannot be derived from this designation. You need an explicitly declared pressure resistance and a matching mounting interface for the specific model.
For the LR18X-B series, LANBAO specifies resistance up to 500 bar and a sensing distance of 2 mm. These figures are a guide to the series, not a universal approval for every installation. For the ordered variant, verify the pressure, temperature, sealing arrangement and operating conditions in the complete documentation.
The same thread diameter does not mean interchangeability. Pitch, screw-in length, seating geometry and seal location are decisive. In addition, the M12 electrical connector says nothing about the process connection. Design the mounting hole according to the manufacturer's drawing; do not seal the sensor in an improvised way.
Illustrative calculation: a pressure of 250 bar corresponds to 25 MPa. A force F = p × A acts on a circular area with a diameter of 8 mm, i.e. approximately 1 260 N. The actual loaded area depends on the design. The example shows the importance of correct fixing; it does not determine the load capacity of any sensor offered.
If switching changes with pressure, also check the movement and deformation of mechanical parts. The symptom may not be caused by the electronics. Recording pressure, temperature and position at the moment of the fault makes it easier to distinguish the causes.
No. It monitors the presence or position of a metal target. To measure pressure, use a pressure transducer with a suitable measuring range.
Only if the manufacturer of the replacement explicitly confirms the required pressure and mounting method. A stainless steel housing alone does not prove pressure resistance.
Simultaneous limit values must be confirmed by the documentation of the specific version. Assess the entire operating range, including the medium and pressure cycles.
High-temperature sensors · Chemical resistance
For a specific selection, prepare the material and dimensions of the target, the working gap, the environmental conditions and the required electrical connection. An overview can be found in the categories Special sensors and Inductive sensors.
Technical documents: LANBAO: LANBAO LR18X-B. This guide helps with selection; binding parameters, wiring and mounting are defined by the documentation of the ordered model.
Techniczne pliki cookies są potrzebne do działania koszyka i zamówienia — są używane zawsze. Analityczne pliki cookies pokazują nam, których stron ludzie szukają i gdzie się gubią, i pomagają nam ulepszać sklep. Użyjemy ich tylko wtedy, gdy na to pozwolisz. Więcej w zasadach przetwarzania danych.
Wybierz, których plików cookies możemy używać. Wybór możesz w każdej chwili zmienić.
Przechowują zawartość koszyka, logowanie i wybrany język oraz chronią formularze przed nadużyciem. Bez nich nie można złożyć zamówienia, dlatego są używane także bez zgody.
Usługa Google Analytics pokazuje nam ruch i zachowanie na stronie w formie zbiorczej. Dzięki temu wiemy, które strony nie działają dla ludzi. Na podstawie tych danych nikogo nie identyfikujemy.