SMC magnetic sensors

SMC D-A (reed) and D-M9 (solid-state) magnetic sensors for sensing piston position in SMC cylinders. Choose by cylinder, wiring and cable.

Filtry
Znaleziono 36 produktów

D-M9BWL, SMC, magnetic sensor, position sensor

Nr kat.: D-M9BWL

D-M9BWL SMC – magnetic sensor. Industrial product for automation, detection or measurement.

Na zapytanie
45,52 €
bez VAT · 55,08 € z VAT

D-M9NVL, SMC, magnetic sensor

Nr kat.: D-M9NVL

D-M9NVL SMC – magnetic sensor, NPN. Industrial product for automation, detection or measurement.

Na zapytanie
45,73 €
bez VAT · 55,33 € z VAT

D-M9PMBPC, SMC, magnetic sensor, position sensor

Nr kat.: D-M9PMBPC

D-M9PMBPC SMC – magnetic sensor, M8, PNP. Industrial product for automation, detection or measurement.

Na zapytanie
45,73 €
bez VAT · 55,33 € z VAT

D-M9NZ, SMC, magnetic sensor, electronic position sensor

Nr kat.: D-M9NZ

D-M9NZ SMC – magnetic sensor, NPN. Industrial product for automation, detection or measurement.

Na zapytanie
48,39 €
bez VAT · 58,56 € z VAT

D-M9PSDPC, SMC, magnetic sensor, position sensor

Nr kat.: D-M9PSDPC

D-M9PSDPC SMC – magnetic sensor, M12, PNP. Industrial product for automation, detection or measurement.

Na zapytanie
50,03 €
bez VAT · 60,54 € z VAT

D-H7A2SAPC, SMC, magnetic sensor, position sensor, connector M8/M12

Nr kat.: D-H7A2SAPC

D-H7A2SAPC SMC – magnetic sensor, M8. Industrial product for automation, detection or measurement.

Na zapytanie
52,50 €
bez VAT · 63,52 € z VAT

D-M9BWVZ, SMC, magnetic sensor, position sensor

Nr kat.: D-M9BWVZ

D-M9BWVZ SMC – magnetic sensor. Industrial product for automation, detection or measurement.

Na zapytanie
52,49 €
bez VAT · 63,52 € z VAT

D-Y7BW, SMC, magnetic sensor, position sensor

Nr kat.: D-Y7BW

D-Y7BW SMC – magnetic sensor. Industrial product for automation, detection or measurement.

Na zapytanie
57,00 €
bez VAT · 68,97 € z VAT

D-F8BL, SMC, magnetic sensor, position sensor

Nr kat.: D-F8BL

D-F8BL SMC – magnetic sensor. Industrial product for automation, detection or measurement.

Na zapytanie
61,10 €
bez VAT · 73,94 € z VAT

D-MP200B, SMC, magnetic sensor, position sensor

Nr kat.: D-MP200B

D-MP200B SMC – magnetic sensor, M8, PNP. Industrial product for automation, detection or measurement.

Na zapytanie
453,76 €
bez VAT · 549,05 € z VAT

Ceny zawierają opłatę recyklingową.

SMC magnetic sensors

The SMC range includes several design generations: you will find D-A93, D-A73, D-A53L and variants D-M9. When replacing, therefore, proceed from the cylinder designation to the supported sensor. Common use for piston monitoring alone does not confirm the same fixing or electrical wiring.

Reed and solid-state variants

SMC distinguishes reed D-A93 and solid-state D-M9. In the D-M9 series, D-M9B is a two-wire version, D-M9P three-wire PNP and D-M9N three-wire NPN. Two wires therefore do not automatically mean a reed contact. The breakdown and parameters of the specific variants are given in the SMC auto-switch catalogue.

For service, it is essential to maintain the function of the whole circuit. Before switching from D-A93 to D-M9B also compare the voltage drop and off-state current with the PLC input. As documentation for the solid-state variant, use the manual D-M9; identical dimensions or a similar code ending do not prove electrical interchangeability.

Procedure for selecting the whole assembly

  1. Write down the cylinder series, its size and the full designation of the original sensor. For an older machine, attach a photo of the existing rail, clamp or slot.
  2. Look up the combination of actuator and sensor in the manufacturer's table. Solve the required fixing together with any bracket; examples of direct, slot and band mounting are given in the SMC selection guide.
  3. Compare the number of wires, output and input function of the control system. Record the wiring before removal so that you do not transfer an unverified assumption to the new assembly.
  4. Determine the cable routing and required length. When working at the cylinder end face, also check the outlet direction and space for service disconnection.
  5. Verify the set point over several working cycles and save the assembly data in the machine documentation.

Example found: D-M9PL

D-M9PL is listed in this category. The manufacturer's selection guide classifies it among three-wire PNP variants with a 3 m cable. For some actuators it appears with a separate bracket BMG2-012. This example shows why the enquiry should contain not only the sensor but also the cylinder type; the mounting combination is not universal. See SMC sensor and bracket tables.

When maintaining several actuators, separate the list of sensors from the list of mounting parts. For each combination, record where it was tested. Do not take a similar cylinder on a neighbouring machine as the only basis for ordering; first compare its designation and the existing installation design.

Common mistakes and FAQ

Is D-M9B a reed sensor?

No, it is one of the solid-state versions. When replacing, follow the full designation and wiring diagram, not just the two connected wires.

Is it enough to take over the position of the old bracket?

Use it as the starting point for the check. After replacement, verify actual switching with the cylinder fitted and record the final setting.

What is often overlooked with a connector replacement?

The exact cable suffix, number of contacts and connector assignment. Record the full assembly designation in the service list so that the next replacement does not require new research.

Other brands can be found among magnetic sensors. Choose the follow-on connection in the category Sensor Cables and Connectors.

Pliki cookies na tej stronie

Techniczne pliki cookies są potrzebne do działania koszyka i zamówienia — są używane zawsze. Analityczne pliki cookies pokazują nam, których stron ludzie szukają i gdzie się gubią, i pomagają nam ulepszać sklep. Użyjemy ich tylko wtedy, gdy na to pozwolisz. Więcej w zasadach przetwarzania danych.