MK1MIP2, EMAS, microswitch, MK1, roller lever, 1 CO
MK1MIP2 EMAS – microswitch, MK1, roller lever, 1 CO. Technical parameters, application and compatibility check.
Cambio 24,43 Kč per 1 EUR. I prezzi sono indicativi, la fatturazione avviene in corone ceche.
EMAS MK1 plastic miniature limit switches with lever or roller. Choose by actuating element.
MK1MIP2 EMAS – microswitch, MK1, roller lever, 1 CO. Technical parameters, application and compatibility check.
MK1PUP1 EMAS – microswitch, MK1, plunger, 1 CO. Technical parameters, application and compatibility check.
MK1KIM1 EMAS – microswitch, MK1, lever, 1 CO. Technical parameters, application and compatibility check.
MK1KIM2 EMAS – microswitch, MK1, lever, 1 CO. Technical parameters, application and compatibility check.
MK1KIM3 EMAS – microswitch, MK1, lever, 1 CO. Technical parameters, application and compatibility check.
MK1KIM4 EMAS – microswitch, MK1, lever, 1 CO. Technical parameters, application and compatibility check.
MK1KIM5 EMAS – microswitch, MK1, lever, 1 CO. Technical parameters, application and compatibility check.
MK1MIM1 EMAS – microswitch, MK1, roller lever, 1 CO. Technical parameters, application and compatibility check.
MK1MIM2 EMAS – microswitch, MK1, roller lever, 1 CO. Technical parameters, application and compatibility check.
MK1MIP1 EMAS – microswitch, MK1, roller lever, 1 CO. Technical parameters, application and compatibility check.
MK1MIP3 EMAS – microswitch, MK1, roller lever, 1 CO. Technical parameters, application and compatibility check.
MK1PUP1Y EMAS – microswitch, MK1, plunger, 1 CO. Technical parameters, application and compatibility check.
I prezzi includono il contributo di riciclaggio.
MK1 switches make it possible to solve mechanical detection in small assemblies. The design must leave space not only for the body, but also for the lever movement and the connection terminals. For sensing for a control input, add a timing question: when does the contact change actually take effect in the program? The mechanical position and the processed information are not the same data.
The public range includes MK1MIP2. Its EMAS sheet states a long lever with a plastic roller, one changeover contact and connection tabs 6.3 × 0.8 mm. These dimensions describe the connection, not the whole switch.
Before mounting, compare the connector receptacle used with the tab size and the conductor. Add space for plugging in, disconnecting and strain relief of the wiring to the sketch. Sometimes the body fits the available space, but once the terminated wires are added the assembly can no longer be safely assembled or removed. This problem is easier to solve on the drawing than during a shutdown.
For a control input, also check the minimum contact load conditions. The OMRON diagnostic overview states that contact problems may also be related to a very small switched load. A high maximum current therefore does not automatically confirm suitability for a weak signal.
Prepare data on the actual input: voltage, current, evaluation method and any filtering. If the catalogue does not provide any of the required properties, list it as an open point of the selection. Merely replacing the contact with a new one may not remove a fault whose cause lies in an unsuitable combination of input and switch.
Consider a model moving part with a speed of 250 mm/s. Processing the input change in the practice control adds a delay of 4 ms. During this time, the movement travels 250 × 0.004 = 1.0 mm. With a model delay of 12 ms, it is already 3.0 mm.
The figures are not the response time of MK1MIP2 nor the setting of a specific PLC. The example merely converts a time difference into a position. It does not include braking, variable speed or further delays. It cannot be used as a calculation of a safe distance or of the exact stopping point of the machine.
The practical conclusion is to also record the input setting during the test. Otherwise, after a program change, the position of the processed event may shift even though the lever and cam have remained in the same place. The mechanical and electrical parts of the diagnostics can thus be compared separately.
The fastening and wire routing must allow the correct working movement. OMRON mounting guidelines for basic switches point out protection against lead pull and dirt. However, the dimensions, forces and permissible travel are determined by the documentation of the specific MK1.
At handover, note the cam contact point, the maximum lever deflection and the return. A common mistake is to test only the electrical switching and overlook that the moving part continues further and loads the actuator outside the designed path.
No. It is one changeover contact; assess the wiring according to its diagram and terminal markings.
Also compare the connection, fastening and actuator. Helpful categories are Plastic Limit Switches MN1 and the common overview Miniature Limit Switches.
I cookie tecnici servono per il funzionamento del carrello e dell'ordine — sono sempre utilizzati. I cookie analitici ci mostrano quali pagine le persone cercano e dove si perdono, e ci aiutano a migliorare il negozio. Li utilizziamo solo se ce lo consenti. Maggiori informazioni nella informativa sul trattamento dei dati.
Scegli quali cookie possiamo utilizzare. Puoi modificare la scelta in qualsiasi momento.
Conservano il contenuto del carrello, l'accesso e la lingua scelta e proteggono i moduli dagli abusi. Senza di essi non è possibile completare l'ordine, per questo sono utilizzati anche senza consenso.
Google Analytics ci mostra in forma aggregata il traffico e il comportamento sul sito. Così capiamo quali pagine non funzionano per gli utenti. In base a questi dati non identifichiamo nessuno.