MKB12-10RZ, SMC, rotary clamp cylinder Ø12mm, stroke 10mm, clockwise
MKB12-10RZ, SMC – pneumatic rotary clamp cylinder; Piston diameter: 12mm; Clamping stroke: 10mm; Direction of rotation when moving from unclamped to clamped: clockwise.
Cambio 24,43 Kč per 1 EUR. I prezzi sono indicativi, la fatturazione avviene in corone ceche.
SMC pneumatic rotary clamps for clamping parts in fixtures. The arm first rotates and then presses down. Choose by size, direction of rotation and clamping force.
MKB12-10RZ, SMC – pneumatic rotary clamp cylinder; Piston diameter: 12mm; Clamping stroke: 10mm; Direction of rotation when moving from unclamped to clamped: clockwise.
MKB12-20LZ, SMC – pneumatic rotary clamp cylinder; Piston diameter: 12mm; Clamping stroke: 20mm; Direction of rotation when moving from unclamped to clamped: counterclockwise.
MKB16-10RZ, SMC – pneumatic rotary clamp cylinder; Piston diameter: 16mm; Clamping stroke: 10mm; Direction of rotation when moving from unclamped to clamped: clockwise.
MKB16-10LZ, SMC – pneumatic rotary clamp cylinder; Piston diameter: 16mm; Clamping stroke: 10mm; Direction of rotation when moving from unclamped to clamped: counterclockwise.
MKB25-30RZ, SMC – pneumatic rotary clamp cylinder; Piston diameter: 25mm; Clamping stroke: 30mm; Direction of rotation when moving from unclamped to clamped: clockwise.
MKB25-30LZ, SMC – pneumatic rotary clamp cylinder; Piston diameter: 25mm; Clamping stroke: 30mm; Direction of rotation when moving from unclamped to clamped: counterclockwise.
I prezzi includono il contributo di riciclaggio.
A pneumatic rotary clamp allows the clamping arm to be swung out of the loading area and then pressed into the fixture. This category offers SMC MKB versions with right-hand and left-hand rotation. Selection starts with the arrangement of the support points and the required arm path; the cylinder diameter alone is not enough to assess the whole assembly.
According to the SMC MK catalogue clamping is carried out in the linear part of the stroke, not during rotation. The standard series requires vertical mounting and a clamping surface perpendicular to the cylinder axis. During clamping, the workpiece must not be moved by an external force in a way that subjects the piston rod to torsion. The manufacturer sets limits on the arm length depending on pressure and also assesses the moment of inertia of the arm relative to the speed of movement. The clamping stroke designation is not the total travel including the rotary part.
For the designer, this means two separate checks are needed: whether the arm passes safely through the space and whether it carries the required load in the end position. Free space with the fixture open does not prove a sufficient reserve for the product at the upper tolerance limit.
The fixture supports should form a clearly defined base. When the product changes, verify again where the clamping force actually acts and whether it causes bending. The machine user also needs access for cleaning the support surfaces; a trapped chip can change the position of the part even though the clamp completes its usual movement.
Consider a model clamping force of 100 N at a distance of 40 mm from the axis. The corresponding static bending moment is M = F·l = 100 × 0.04 = 4 N·m. Extending the arm to 80 mm while keeping the same clamping force means 8 N·m. The same force requirement therefore does not mean the same stress.
This is a general calculation, not the permitted load of a specific MKB. It does not include the dynamics of rotation, the arm mass or design limitations. In the project, compare the actual geometry and operating pressure with the documentation of the selected model; simply increasing the pressure is not a universal solution for an arm that is too long.
Before the first working cycle, verify the correct direction of rotation according to the manufacturer's drawing and the actual mounting orientation. Check the entire movement for collisions and then repeat with the limit dimensions of the part. Carry out adjustments in the safe mode of the machine. Before dismantling, secure the part against release and safely depressurise the circuit.
If the product position changes, record the cleanliness of the supports, the part dimension, the clamping pressure and the position reached. Look for a link with a specific change instead of adjusting several parameters at once. For the air supply, see air preparation and for motion control pneumatic valves.
No. The length changes the bending moment and the mass distribution. A new arm is a design change that requires new verification.
Here we primarily deal with clamping into a fixed fixture. For handling grips, compare gripper heads and assess separately how the part is held during movement.
I cookie tecnici servono per il funzionamento del carrello e dell'ordine — sono sempre utilizzati. I cookie analitici ci mostrano quali pagine le persone cercano e dove si perdono, e ci aiutano a migliorare il negozio. Li utilizziamo solo se ce lo consenti. Maggiori informazioni nella informativa sul trattamento dei dati.
Scegli quali cookie possiamo utilizzare. Puoi modificare la scelta in qualsiasi momento.
Conservano il contenuto del carrello, l'accesso e la lingua scelta e proteggono i moduli dagli abusi. Senza di essi non è possibile completare l'ordine, per questo sono utilizzati anche senza consenso.
Google Analytics ci mostra in forma aggregata il traffico e il comportamento sul sito. Così capiamo quali pagine non funzionano per gli utenti. In base a questi dati non identifichiamo nessuno.