Pneumatic cylinders

SMC and Festo pneumatic cylinders – ISO, compact, miniature, round, guided and rodless. Choose by bore, stroke, required force, mounting and position sensing.

Filtros
Encontrado 414 productos

MKB32TF-30RZ, SMC, rotary clamp cylinder, diameter 32 mm, stroke 30 mm

N.º cat.: MKB32TF-30RZ

MKB32TF-30RZ, SMC, rotary clamp cylinder, diameter 32 mm, stroke 30 mm. A pneumatic cylinder converts the energy of compressed air into linear motion.

Bajo consulta
250,10 €
sin IVA · 302,62 € con IVA

MXZ16L-15L, SMC, compact slide

N.º cat.: MXZ16L-15L

MXZ16L-15L, SMC, compact slide. A linear slide or carriage combines linear motion with precise mechanical guidance.

Bajo consulta
250,51 €
sin IVA · 303,12 € con IVA

MGPM16-125Z, compact cylinder, SMC

N.º cat.: MGPM16-125Z

MGPM16-125Z, compact cylinder, SMC

Bajo consulta
252,96 €
sin IVA · 306,09 € con IVA

MGPA16-10Z, compact cylinder, SMC

N.º cat.: MGPA16-10Z

MGPA16-10Z, compact cylinder, SMC

Bajo consulta
254,19 €
sin IVA · 307,57 € con IVA

MXH10-5Z, SMC, compact precision slide

N.º cat.: MXH10-5Z

MXH10-5Z, SMC, compact precision slide. A linear slide or carriage combines linear motion with precise mechanical guidance.

Bajo consulta
256,23 €
sin IVA · 310,04 € con IVA

ADN-100-100-A-P-A, Festo, 536372, compact cylinder

N.º cat.: ADN-100-100-A-P-A

ADN-100-100-A-P-A, Festo, 536372, compact cylinder. The air preparation element filters, regulates or otherwise prepares the compressed air for the pneumatic system.

Bajo consulta
261,54 €
sin IVA · 316,47 € con IVA

MGPA16-30Z, compact cylinder, SMC

N.º cat.: MGPA16-30Z

MGPA16-30Z, compact cylinder, SMC

Bajo consulta
268,90 €
sin IVA · 325,37 € con IVA

CDA2B50-300Z, round cylinder with tie rods, SMC

N.º cat.: CDA2B50-300Z

CDA2B50-300Z, round cylinder with tie rods, SMC

Bajo consulta
270,13 €
sin IVA · 326,85 € con IVA

MGPA20TF-20Z, compact cylinder, SMC

N.º cat.: MGPA20TF-20Z

MGPA20TF-20Z, compact cylinder, SMC

Bajo consulta
277,40 €
sin IVA · 335,66 € con IVA

DSBC-100-25-PPSA-N3, pneumatic cylinder, 1384890, Festo

N.º cat.: DSBC-100-25-PPSA-N3

pneumatic cylinder; stroke: 25mm; piston diameter: 100mm; 1384890; Festo

Bajo consulta
277,89 €
sin IVA · 336,25 € con IVA

MGPM20-100Z, compact cylinder, SMC

N.º cat.: MGPM20-100Z

compact cylinder; piston diameter: 20mm; stroke: 100; SMC

Bajo consulta
281,57 €
sin IVA · 340,70 € con IVA

MGPM32TF-50Z, SMC, pneumatic cylinder, slide bearing, diameter 32 mm, stroke 50 mm, magnet

N.º cat.: MGPM32TF-50Z

MGPM32TF-50Z, SMC, pneumatic cylinder, slide bearing, diameter 32 mm, stroke 50 mm, magnet. A guided cylinder combines linear motion with guidance against rotation and lateral load.

Bajo consulta
285,66 €
sin IVA · 345,64 € con IVA

C96SDB80-730C, SMC, round cylinder with tie rods, diameter 80 mm, stroke 730 mm, magnet

N.º cat.: C96SDB80-730C

C96SDB80-730C, SMC, round cylinder with tie rods, diameter 80 mm, stroke 730 mm, magnet. An ISO/VDMA cylinder is a standardised pneumatic actuator for industrial machines and automation.

Bajo consulta
285,66 €
sin IVA · 345,64 € con IVA

MGPL25TF-50Z, SMC, pneumatic cylinder with linear guide, diameter 25 mm, stroke 50 mm, magnet

N.º cat.: MGPL25TF-50Z

MGPL25TF-50Z, SMC, pneumatic cylinder with linear guide, diameter 25 mm, stroke 50 mm, magnet. A guided cylinder combines linear motion with guidance against rotation and lateral load.

Bajo consulta
300,33 €
sin IVA · 363,40 € con IVA

MGPM25-100Z, compact cylinder, SMC

N.º cat.: MGPM25-100Z

compact cylinder; piston diameter: 25mm; stroke: 100; SMC

Bajo consulta
305,88 €
sin IVA · 370,12 € con IVA

MGPM32-50Z, SMC, compact cylinder, diameter 32 mm, stroke 50 mm

N.º cat.: MGPM32-50Z

MGPM32-50Z, SMC, compact cylinder, diameter 32 mm, stroke 50 mm. A guided cylinder combines linear motion with guidance against rotation and lateral load.

Bajo consulta
308,54 €
sin IVA · 373,33 € con IVA

DFM-12-20-P-A-KF, Festo, guided cylinder, 170900

N.º cat.: DFM-12-20-P-A-KF

DFM-12-20-P-A-KF, Festo, guided cylinder, 170900. A pneumatic cylinder converts the energy of compressed air into linear motion.

Bajo consulta
309,77 €
sin IVA · 374,82 € con IVA

MGQL20TF-20, compact cylinder, SMC

N.º cat.: MGQL20TF-20

compact cylinder; stroke: 20; piston diameter: 20; double-acting; SMC

Bajo consulta
312,22 €
sin IVA · 377,79 € con IVA

MGPM25R-50Z, SMC, compact cylinder, slide bearing, water-resistant version, diameter 25 mm, stroke 50 mm

N.º cat.: MGPM25R-50Z

MGPM25R-50Z, SMC, compact cylinder, slide bearing, water-resistant version, diameter 25 mm, stroke 50 mm. A guided cylinder combines linear motion with guidance against rotation and lateral load.

Bajo consulta
314,67 €
sin IVA · 380,75 € con IVA

CDA2F80-180Z, SMC, round cylinder with tie rods, diameter 80 mm, stroke 180 mm

N.º cat.: CDA2F80-180Z

CDA2F80-180Z, SMC, round cylinder with tie rods, diameter 80 mm, stroke 180 mm. A pneumatic cylinder converts the energy of compressed air into linear motion.

Bajo consulta
317,12 €
sin IVA · 383,72 € con IVA

Rodless cylinder, MY1B25TFG-670Z, diameter 25mm, stroke 670mm, SMC

N.º cat.: MY1B25TFG-670Z

Rodless cylinder, diameter 25mm, stroke 670mm, mechanical force transmission, slide bearing, air supplies on one side

Bajo consulta
355,13 €
sin IVA · 429,71 € con IVA

MGPM20TF-50Z, SMC, pneumatic cylinder, linear guide, diameter 20 mm, stroke 50 mm

N.º cat.: MGPM20TF-50Z

MGPM20TF-50Z, SMC, pneumatic cylinder, linear guide, diameter 20 mm, stroke 50 mm. A guided cylinder combines linear motion with guidance against rotation and lateral load.

Bajo consulta
361,26 €
sin IVA · 437,12 € con IVA

Los precios incluyen la tasa de reciclaje.

Pneumatic cylinders

A pneumatic cylinder converts the energy of compressed air into linear motion. It moves a part, presses a tool or operates a mechanism. The range includes, for example, the SMC CJP, CQ2, CQS, CD85, JCQ, MGP and MY1 series as well as Festo cylinders. In addition to actuators, there are GKM clevises and KJ rod ends; when ordering, therefore, distinguish the cylinder itself from its accessories.

Principle: pressure, area and direction of movement

Pressure acts on the effective area of the piston. In a double-acting cylinder, air is supplied alternately to both chambers and the opposite chamber is exhausted. A single-end rod reduces the area for retracting, so at the same overpressure the theoretical force is lower than when extending. This difference is also shown by SMC force table C95.

In the single-acting version with a return spring, air provides the working movement and the spring the return. When extending, its resistance must also be overcome. The design is illustrated by SMC CJP manual. Single-acting and double-acting versions therefore require a different assessment of the working and return movement.

Selection by task and space

First determine the required stroke, the direction of load and the force during the whole cycle. Then compare the diameter, permissible pressure, speed and temperature of the specific version. Check the dimensions in the retracted and extended position, the body mounting, the piston rod end and the space for connection. It is not enough to select only the same diameter and stroke.

A lateral load requires a separate assessment of the guide. For example, SMC MGP connects the cylinder with a guide structure. The force in the axis of movement is not the same as the permissible load on the guide. When replacing, compare the full order code and drawing; a similar series designation does not guarantee an identical version.

For an enquiry, prepare a description of the working cycle: what moves, from where to where, with what load and how often. For a replacement, add a photo of the nameplate and mounting. Write down the required properties and data not yet verified separately; this makes checking the offered version easier.

Our own model calculation: force difference

Let us consider a fictitious double-acting cylinder with a piston diameter D = 30 mm, a piston rod d = 12 mm and an overpressure p = 0.45 MPa. In the model, the opposite chamber has zero overpressure; we neglect friction and dynamics. Since 1 MPa = 1 N/mm², the area for extending A = πD²/4 is 706.9 mm² and the force F = pA approximately 318.1 N. For retracting, A = π(D² − d²)/4 = 593.8 mm² and F approximately 267.2 N.

The difference is 50.9 N. This is our own tutorial model, which does not define product selection or a guaranteed force. An actual design must take into account back pressure, friction, load and an operating reserve.

Mounting and commissioning

Before intervention, secure the load, disconnect the energy supplies and release residual pressure. Align the cylinder axis with the guide of the mechanism and verify free movement over the whole stroke. Protect the piston rod from scratches and the fittings from dirt. Set the speed gradually from a low value; also verify the permissible end-of-stroke energy. The procedure is detailed in SMC manual CQ2.

Diagnostics of irregular movement

In case of jerking or loss of force, check the pressure during operation, the patency of the supply, the speed setting, leaks and alignment. Compare the change in cycle time with the original state. Increasing pressure without finding the cause can mask a mechanical problem. In case of hard end-of-stroke impact, assess speed and load; separate shock absorbers select according to the specific energy requirement.

FAQ

Does the theoretical force value guarantee the actual force on the part?

No. It is the ideal result of pressure and area; the actual movement is also affected by back pressure and mechanical resistance.

Can a position sensor be added to every cylinder?

Verify compatibility for the specific cylinder, its equipment and mounting method. The range can be found among with magnetic sensors; the similarity of the slot alone is not enough.

Cookies en este sitio web

Necesitamos las cookies técnicas para que funcionen el carrito y el pedido — se usan siempre. Las cookies analíticas nos muestran qué páginas buscan las personas y dónde se pierden, y nos ayudan a mejorar la tienda. Solo las usaremos si nos lo permites. Más información en la política de tratamiento de datos.