AG0811-S, TIBOX, plastic installation box, 80×110×45mm
AG0811-S, TIBOX: plastic installation box with outer dimensions 80×110×45mm; the mounting plate MP0811 is a separate accessory.
Tipo de cambio 24,43 Kč por 1 EUR. Los precios son orientativos; la facturación se realiza en coronas checas.
Tibox, Famatel and other plastic terminal boxes for branching and terminating cables. Choose by size, protection rating, material and number of cable glands.
AG0811-S, TIBOX: plastic installation box with outer dimensions 80×110×45mm; the mounting plate MP0811 is a separate accessory.
68050, Famatel SolidBOX, plastic installation box 135×74×72mm, IP65, ABS, IK07, opaque lid and smooth sides. Surface mounting.
Compact Tibox plastic terminal box PBT-4P for connecting four electrical lines on an integrated four-pole terminal block. The version has dimensions of 60×40×24mm and a protection rating of IP66.
PBT-6P, Tibox, plastic terminal box, 6 poles, 70×50×24mm. The PBT-6P type box is designed to house a terminal block connection; size 70×50×24mm corresponds to the manufacturer's catalogue table.
TJ-10P, Tibox, plastic terminal box, 10 poles, 110×75×40mm. The TJ-10P type box is designed to house a terminal block connection; size 110×75×40mm corresponds to the manufacturer's catalogue table.
Los precios incluyen la tasa de reciclaje.
A plastic terminal box must accommodate not only the connecting elements themselves but also the incoming cables and their terminations. A selection by length and width without checking the internal layout is usually incomplete. The current listing includes AG0811-S, PBT-4P, PBT-6P, Tibox TJ-10P and Famatel 68050 Solidbox. Use these names to identify the specific offer, not as a common specification for all boxes.
List the number of incoming cables, the number of their cores, cross-sections and the required connections. Each terminal needs its place, but access also requires the stripped conductor end and a mounting tool. Design the marking of the connections separately. For a service box, the diagram should be understandable even after a long time and without guessing which cable belongs to which device.
Transfer the actual internal obstacles to the drawing: lid posts, mounting points and any rail or base plate. Do not confuse the outer footprint with the usable floor area. Also check the height needed above the terminal where the lid closes. Prepared conductors should not become a mechanical support for the lid.
The Fibox material overview distinguishes polycarbonate and ABS and points out differences under UV exposure as well as the lack of inherent EMC shielding of these plastics. This is general documentation for asking the right questions, not confirmation of the material or resistance of a specific Tibox or Famatel model.
For the selected code, therefore verify the type of plastic, the conditions of use and the lid design. For placement near a machine, add information on cleaning agents, liquids and temperature. The designation “plastic” alone is not enough to decide on chemical resistance or permanent exposure to sunlight. If protection of a sensitive signal is needed, its solution must be part of the design of the cabling and the whole assembly.
For each cable, record the outer diameter and direction of approach. A gland is also selected according to its clamping range and mounting interface; the hole size is not the only parameter. Before laying out the entries, check whether their outer parts fit side by side and whether access to the fixing remains. Also take into account other connected parts that may restrict the space.
The protection rating of the finished assembly cannot be documented by simply copying the figure of the empty box. What matters are correctly chosen and fitted entries, sealed unused holes and the condition of the seals. The procedure for modifications and closing must be based on the documentation of the specific product. Electrical wiring and its inspection must be carried out by a qualified person.
Imagine a usable width of 90 mm, a terminal assembly 50 mm wide and a requirement to leave 15 mm on each side for routing. 10 mm remains. This is only a model spatial sum: it does not verify hole spacing, minimum cable bending radius or tool access. Therefore draw the result into the actual drawing rather than automatically concluding that any box 90 mm wide is suitable.
Confirm whether terminals, a rail, a mounting base plate or glands are included in the delivery. A photo of a fitted example does not replace a bill of materials. For larger device assemblies, also compare control cabinet enclosure; replacing a small box with a larger one does not automatically solve all mounting requirements.
Do not infer it without documentation. The number of connections follows from your diagram, while the commercial code may denote various product properties.
Also compare the depth, internal mounting points, entries, lid and conditions of use. The same length and width do not confirm interchangeability.
Necesitamos las cookies técnicas para que funcionen el carrito y el pedido — se usan siempre. Las cookies analíticas nos muestran qué páginas buscan las personas y dónde se pierden, y nos ayudan a mejorar la tienda. Solo las usaremos si nos lo permites. Más información en la política de tratamiento de datos.
Elige qué cookies podemos usar. Puedes cambiar tu elección en cualquier momento.
Guardan el contenido del carrito, el inicio de sesión y el idioma elegido, y protegen los formularios frente a abusos. Sin ellas no se puede finalizar el pedido, por eso se utilizan incluso sin consentimiento.
Google Analytics nos muestra de forma agregada el tráfico y el comportamiento en el sitio. Así sabemos qué páginas no funcionan para los usuarios. Con estos datos no identificamos a nadie.