LR30XCF10ATC-E2, LANBAO, inductive sensor 2-wire, M30, Sn 10 mm, 2-wire, NC, connector M12/4 pins

LR30XCF10ATC-E2 – Two-wire inductive proximity sensor

LR30XCF10ATC-E2 is a two-wire inductive proximity sensor from LANBAO, size M30. It detects metal objects without contact and switches in series with the load, so it needs only two wires — supply and signal share the same pair.

Key features

• Sensing distance 10 mm – rated value for a standard steel target.
• Output 2-wire, NC contact – normally closed – connects to a PLC digital input or a relay coil.
• Supply 20–250 V AC.
• Flush mounting.
• Connection: connector M12/4 pins.
• Degree of protection IP67 – protection against dust and temporary immersion.

How an inductive sensor works

The coil in the sensing face generates a high-frequency magnetic field. When a metal object enters the field, it induces eddy currentsin its surface, which draw energy from the field and dampen it. As soon as the damping exceeds the set threshold, the evaluation circuit switches the output. All this happens without any contact, so the sensor has no mechanically wearing parts.

High-frequency oscillation principle: coil field, eddy currents in the metal target and their damping effect.

Correction factor – why the range on aluminium differs from steel

The rated sensing distance applies to a standard steel target. For other metals it is reduced by a correction factor. Calculate the actual distance as the rated Sn multiplied by the material factor.

Standard target and tolerance

According to the manufacturer's catalogue, the standard target is a square plate of St37 steel, 1 mm thick. The side length equals the larger of: the diameter of the sensing face, or three times the sensing distance. A smaller target means a shorter range. The sensing distance tolerance is ±10 %, so never set the working point exactly at the Sn limit.

Technical specifications LR30XCF10ATC-E2

Wiring of LR30XCF10ATC-E2 by wire colours

A two-wire AC sensor is connected in series with the load – a contactor, relay or AC PLC input. It has no separate signal wire.

Caution: according to the manufacturer's catalogue, two-wire AC sensors must not be connected in AND or OR logic and must not be in series with a mechanical contact.

For the connector version, check the pin assignment in the datasheet of this model – for AC sensors it differs between series.

The colour coding complies with IEC 60947-5-2. Always compare the actual pin and wire assignment with the diagram in the sensor datasheet (Downloads tab).

Two-wire connection – the load is in series with the sensor.

Mounting and free space

The sensor has a flush sensing face, so it can be screwed into a metal structure right up to the face without affecting its function. The trade-off is a shorter sensing distance compared to the non-flush version.

Flush mounting: the face may be level with the metal.

Mutual interference of sensors

Two sensors mounted close to each other may interfere with each other. If you need to sense at two adjacent points, keep the lateral spacing given in the sensor's dimension drawing, or offset the sensors so that their faces do not point into the same space.

Set the working distance to 70 to 80 % of the rated Sn, i.e. safely below 10 mm for this model. The tolerance is ±10 % and the distance also changes with temperature and supply voltage.

Connection cable for LR30XCF10ATC-E2

The sensor has a connector M12, 4 pins, male (external thread with pins), so it requires a cable with a femaleconnector. The cable is not included.

• QE12-N4G5-N – M12, 4 pins, female, angled 90°, 5 m, PVC, with LED indication

In this NC version the output is on pin 2, which a three-pin cable does not contain, so choose a four-pin cable.

PUR version: we do not yet stock a M12 female cable with a PUR jacket (for oils, coolant emulsions, abrasion, low temperatures and drag-chain installation). Contact us and we will source it. A cable with a PVC jacket is intended for normal dry machine environments.

The LED indication of the switched output in the connector is designed for the PNP NO version. With other output combinations the cable works electrically, but the indicator may not show switching – in that case choose a cable without indication.

The same sensor with a different connection

• LR30XCF10ATC – the same sensor with a fixed cable 2 m

Typical applications

• retrofitting existing installations where only a two-core cable is laid
• replacing a mechanical limit switch without re-pulling the cabling
• saving wires and terminals in the control cabinet on large machines
• series connection with a relay, contactor or PLC input
• simple signalling and monitoring circuits

How to choose and what to watch out for

• Flush mounting: the sensor can be screwed into a metal structure right up to the face without affecting its function. Compared to the non-flush variant, however, it has a shorter sensing distance.
• Two-wire connection: the sensor is connected in series with the load. Before use, check the residual current and voltage drop against the minimum values of the input you are connecting the sensor to.
• NC contact (normally closed): the output is active at rest and opens on detection. It is used where a broken wire should cause the same reaction as a detection (safer logic).
• Connector connection M12/4 pins: a separate connection cable with a matching connector is required for operation – you will find it in the Cables with connector category.
• Degree of protection IP67: protection against dust and temporary immersion. Not designed for permanent immersion or high-pressure washing – this requires IP69K.
• Sensing distance 10 mm is the rated value for a standard steel target. For stainless steel, brass, aluminium or copper it is reduced by a reduction factor – if you detect non-ferrous metals, allow a margin or choose a model with correction factor 1.

NO or NC – and why it is not just a matter of convenience

NO (normally open) is an output that is active on detection. NC (normally closed) is active at rest and opens on detection. The difference is a safety one: with NC, a broken wire causes the same reaction as a detection, so the fault shows up immediately. With NO, a broken cable remains unnoticed until someone tries to switch.

This model has the contact NC – normally closed.

Similar models in the same series

• LR30XBF10DLC
• LR30XBF10DLC-E2
• LR30XBF10DLO
• LR30XBF10DLO-E2
• LR30XCF10ATC

Frequently asked questions

Does LR30XCF10ATC-E2 have a PNP or NPN output?

LR30XCF10ATC-E2 has a 2-wire output with an NC contact – normally closed. Check that your PLC input matches this output type.

What is the sensing distance of LR30XCF10ATC-E2?

The sensing distance (Sn) is 10 mm. This is the rated value for a standard steel target; the range is shorter for non-ferrous metals.

How is LR30XCF10ATC-E2 connected?

LR30XCF10ATC-E2 is supplied with the connection: connector M12/4 pins. A connection cable with a matching connector must be ordered separately.

Which cable do I need for LR30XCF10ATC-E2?

Cable with a female M12 connector. We stock QE12-N4G5-N (4 pins, 5 m, PVC); for sensors with one output, three-pin QE12-N3G5-P or QE12-N3G5-N. can also be used. The cable is not included.

What is the difference compared to a three-wire PNP/NPN sensor?

A two-wire sensor is connected in series with the load and does not need a separate signal wire. It saves one core in the cable, but a residual current flows through it and it has a higher voltage drop, which must be taken into account with sensitive PLC inputs.

A detailed datasheet with a dimension drawing and wiring diagram can be found in the tab Downloads.