PSK12, EMAS, box for main switches, 3-4f 10A-25A
PSK12 EMAS - cabinet for cam switch. Technical specifications, use, assembly and selection of the correct variant.
Árfolyam 24,43 Kč / 1 EUR. Az árak tájékoztató jellegűek, a számlázás cseh koronában történik.
Accessories for EMAS cam switches – enclosures, contact bodies and labels. Choose by switch series.
PSK12 EMAS - cabinet for cam switch. Technical specifications, use, assembly and selection of the correct variant.
PSK21 EMAS - cabinet for cam switch. Technical specifications, use, assembly and selection of the correct variant.
PSK22 EMAS - case for cam switch. Technical specifications, use, assembly and selection of the correct variant.
PSK11 EMAS - case for cam switch. Technical specifications, use, assembly and selection of the correct variant.
Az árak tartalmazzák az újrahasznosítási díjat.
The applicability of the solenoid starters determines whether the selected device actually fits into the assembly, whether it can be properly controlled, and whether it is possible to meet environmental requirements. The box is not an electrical substitute for another type of starter. Its selection therefore depends on the complete specification of the device, the contact body dimensions, and the mounting method.
In the TECHNOLINE range, for example, you will find PSK11, PSK12, PSK21 and PSK22. EMAS distinguishes in the PSK series sizes for devices 10–25 A and 32–40 A and for different numbers of contact bodies. The number of bodies cannot be replaced by the number of control positions without a drawing. Two devices with the same current may require different space.
Specifically PSK12 manufacturer determines for 10-25 A and three to four bodies; specifies IP54 for this box. This does not prove the shielding of the final assembly with the starter and cable inputs. The assessment applies to the entire installation, not just the highest IP of some components.
First check if the manufacturer specifies the given combination of starter and box. Then compare the position of the locking, depth behind the body, and space for the contacts. Next, check the cable access: the cable can enter the enclosure, but it must have space for its allowed flex and slackening of the pull. The outer dimensions are not a substitute for usable internal space.
Besides geometry, consider the orientation of the label and handle. After installation, the marked positions must correspond to the actual function and be readable from the service area. The additional label 'main switch' or color change does not constitute a safety feature that the manufacturer did not specify. The applicability also does not increase the rated current.
Consider only the illustrative design: between the mounting plane and the inner wall, there is 95 mm. The body of the starter takes up 55 mm in this example, the designed space for cable routing 25 mm, and the mounting reserve 10 mm. The required depth is 55 + 25 + 10 = 90 mm, i.e., with a difference of 5 mm. The numbers are not the PSK12 dimensions or universal minimum spacing.
The result only means that one dimensional sum has been achieved. It has not verified the width, collision of weights with the passage, the curvature radius of the specific cable, or tool access. If the contact body is extended by 12 mm, the same design now requires 102 mm and does not comply. The same front switch can still be retained.
For the finished assembly, specify the tightening conditions, used inputs, and unused openings. When changing the cable routing, check that you do not transfer the load to the contacts or mechanism. The box must allow the pre-defined installation and maintenance; a tight closure must not deform the starter. The actual connections and verification of electrical safety measures should be done by a professionally skilled person.
No. You need the exact type, compatibility and spatial design. Current size and number of contact bodies are different selection aspects.
This cannot be expected without verification. Compare relevant On / Off Switches 60 ° and On / Off Safety switches 90 ° by code and drawing. Select the default function in the overview first Vacuum cleaners.
A technikai sütikre a kosár és a rendelés működéséhez van szükség — ezeket mindig használjuk. Az analitikai sütik megmutatják, mely oldalakat keresik az emberek és hol akadnak el, és segítenek javítani a webáruházat. Ezeket csak akkor használjuk, ha engedélyezi. Bővebben: adatkezelési tájékoztatóban.
Válassza ki, mely sütiket használhatunk. A választást bármikor módosíthatja.
Megőrzik a kosár tartalmát, a bejelentkezést és a kiválasztott nyelvet, és védik az űrlapokat a visszaélésektől. Nélkülük a rendelés nem fejezhető be, ezért hozzájárulás nélkül is használjuk őket.
A Google Analytics összesített formában mutatja meg a weboldal látogatottságát és a felhasználói viselkedést. Ebből tudjuk meg, mely oldalak nem működnek jól. Ezek alapján senkit nem azonosítunk.